PID-Py 0.2.10

Simple (but complete) PID controller in Python

PID_Py

PID_Py provide a PID controller written in Python. This PID controller is simple to use, but it's complete.

:bangbang: Non-responsability :bangbang:

I am not responsible for any material or personal damages in case of failure. Use at your own risk.

Installation

python3 -m pip install PID_Py

Usage

Minimum usage

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In this usage the PID as no limitation, no history and the PID is in direct action (Error increasing -> Increase output).

Indirect action PID

If you have a system that required to decrease command to increase feedback, you can use indirectAction parameters.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, indirectAction = True)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

Limiting output

If your command must be limit you can use outputLimits parameters.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, outputLimits = (0, 100))

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

By default the value is (None, None), which implies that there is no limits. You can activate just the maximum limit with (None, 100). The same for the minimum limit (-100, None).

Historian

If you want to historize PID values, you can configure the historian to record values.

from PID_Py.PID import PID
from PID_Py.PID import HistorianParameters

# Initialization
historianParameters = HistorianParamters.SETPOINT | HistorianParameters.PROCESS_VALUE
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, historianParameters = HistorianParameters)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

...

# PID Historian
import matplotlib.pyplot as plt

plt.plot(pid.historian["TIME"], pid.historian["SETPOINT"], label="Setpoint")

plt.plot(pid.historian["TIME"], pid.historian["PROCESS_VALUE"], label="Process value")

plt.legend()
plt.show()

In the example above, the PID historian records setpoint, processValue and time. Time is the elapsed time from the start. After that a graphic is draw with matplotlib.

Historian parameters list

• P : proportionnal part
• I : integral part
• D : derivative part
• ERROR : PID error
• SETPOINT : PID setpoint
• PROCESS_VALUE : PID process value
• OUTPUT : PID output

The maximum lenght of the historian can be choose. By default it is set to 100 000 record per parameter. Take care about your memory.

In example for one parameters. A float value take 24 bytes in memory. So 100 000 floats take 2 400 000 bytes (~2.3MB).

For all parameters it takes 16 800 000 bytes (~16MB). It's not big for a computer, but if PID is executed each millisecond (0.001s), 100 000 record represent only 100 seconds of recording.

If you want to save 1 hour at 1 millisecond you will need 3 600 000 records (~82.4MB) for one parameter, and for all parameters it will takes ~576.8MB.

For a raspberry pi 3 B+ it's the half of the RAM capacity (1GB)

Proportionnal on measurement

This avoid a strong response of proportionnal part when the setpoint is suddenly changed.

This change the P equation as follow :

• False : P = error * kp
• True : P = -(processValue * kp)

This result in an augmentation of the stabilization time of the system, but there is no bump on the output when the setpoint change suddenly. There is no difference on the reponds to process disturbance.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, proportionnalOnMeasurement=True)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

Integral limitation

The integral part of the PID can be limit to avoid overshoot of the output when the error is too high (When the setpoint variation is too high, or when the system have trouble to reach setpoint).

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, integralLimit = 20.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the integral part of the PID is clamped between -20 and 20.

Derivative on measurement

This avoid a strong response of derivate part when the setpoint is suddenly changed.

This change the D equation as follow :

• False : D = ((error - lastError) / dt) * kd
• True : D = -(((processValue - lastProcessValue) / dt) * kd)

The effect is there is no bump when the setpoint change suddenly, and there is no difference on the responds to process disturbance.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, derivativeOnMeasurement=True)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

Integral freezing

When a known disturbance occur, the integral part can be freezed to avoid increasing of its value during the perturbance. For example, in a oven. When temperature is stable, and the door is opened the temperature drops quickly. And when the door is closed again, the temperature will rise to the previous temperature. So integral part value don't need to be increased to reach temperature setpoint.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0)

...

pid.integralFreezing = doorIsOpened

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the integral part value is freezed when the door is open. When the door is closed the integral part value resumes its calculation.

Deadband

A deadband can be set, by default its deactivated. It can be activated by entering a value to deadband. When the error is between [-deadband, deadband] for deadbandActivationTime (in second) the integral is no longer calculated. If the error exceed deadband the integral part recalculated.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, deadband=1.0, deadbandActivationTime = 10.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the PID behaves normally until the error is lower than 1 for 10 seconds. The integral part stops. Then when the error is higher than 1.0 the integral is recalculated.

Setpoint ramp

The setpoint variation can be limited with setpointRamp option. This option allow to make a ramp with the setpoint when this one change.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, setpointRamp=10.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the setpoint has a maximal ramp of 10 units per second. If the setpoint is change to 10 from 0, the real setpoint used will change for 1 second to 10.0. The same behavior in negative, but with -setpointRamp.

Setpoint reached by the process value

The PID can return that the process value is stable on the setpoint. To configure it use setpointStableLimit to define the maximum difference between the process value and the setpoint (error) to considered the setpoint reached. And use setpointStableTime to define an amount of time to considered the setpoint reached

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, setpointStableLimit=0.1, setpointStableTime=1.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example abose, the output setpointReached is set to True when the error is between -0.1 and +0.1 for 1.0 second. If the error exceed +/- 0.1, the output is reset.

Process value stabilized indicator

The PID can return that the process value is stabilized, to configure it use processValueStableLimit to define the maximum variation when the process value is stable, and processValueStableTime to define the amount of time when the variation is below the limit.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, processValueStableLimit=0.1, processValueStableTime=1.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the output processValueStabilized is set to True when the process value variation do not exceed +/- 0.1 unit/s for 1.0 second. If the process value variation exceed +/- 0.1 unit/s the output processValueStabilized is set to False.

Manual mode

The PID can be switch in manual mode, this allow to operate output directly through manualValue.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0)

...

# Manual mode
pid.manualMode = True
pid.manualValue = 12.7

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, command will be always equal to 12.7. The PID calculation is no longer executed. The integral part is keep equal to output minus proportionnal part, this allow a smooth switching to automatic.

To avoid bump when switching in manual there is bumplessSwitching attribute. This attributes keep manualValue equal to output.

If you disable this function you will have bump when you switch in manual mode with manualValue different of output. If this case you can destabilise (:heavy_exclamation_mark:) your system. Be careful

Logging

The PID can use a logger (logging.Logger built-in class) to log event. Logging configuration can be set outside of the PID. See logging.Logger documentation.

from PID_Py.PID import PID
import logging

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, logger = logging.getLogger("PID"))

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the PID will send event on the logger. The logger can also get with the name.

pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, logger = "PID")

Threaded PID

With the threaded PID you don't have to call pid(processValue, setpoint). It's call as fast as possible or with a constant cycle time. When you want to stop the PID use quit attribute to finish the current execution and exit.

from PID_Py.PID import ThreadedPID

# Initialization
pid = ThreadedPID(kp = 0.0, ki = 0.0, kd = 0.0, cycleTime = 0.01)
pid.start()

...

# PID inputs
pid.setpoint = targetValue
pid.processValue = feedback

# PID output
command = pid.output

...

# Stop PID
pid.quit = True
pid.join()

In the example above the threaded PID is created with 10ms (0.01s) of cyclic time. It means that the calculation is executed each 10ms.