PID-Py 0.2.2

Simple (but complete) PID controller in Python

PID_Py

PID_Py provide a PID controller wrote in Python. This PID controller is simple to use, but it's complete.

:bangbang: Non-responsability :bangbang:

I am not responsible for any material or personal damages in case of failure. Use at your own risk.

Installation

python3 -m pip install PID_Py

Usage

Minimum usage

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In this usage the PID as no limitation, no history and the PID is in direct action (Error increasing -> Increase output).

Indirect action PID

If you have a system that required to decrease command to increase feedback, you can use indirectAction parameters.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, indirectAction = True)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

Limiting output

If your command must be limit you can use outputLimits parameters.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, outputLimits = (0, 100))

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

By default the value is (None, None), which implies that there is no limits. You can activate just the maximum limit with (None, 100). The same for the minimum limit (-100, None).

Historian

If you want to historize PID values, you can configure the historian to record values.

from PID_Py.PID import PID
from PID_Py.PID import HistorianParameters

# Initialization
historianParameters = HistorianParamters.SETPOINT | HistorianParameters.PROCESS_VALUE
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, historianParameters = HistorianParameters)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

...

# PID Historian
import matplotlib.pyplot as plt

plt.plot(pid.historian["TIME"], pid.historian["SETPOINT"], label="Setpoint")

plt.plot(pid.historian["TIME"], pid.historian["PROCESS_VALUE"], label="Process value")

plt.legend()
plt.show()

In the example above, the PID historian records setpoint, processValue and time. Time is the elapsed time from the start. After that a graphic is draw with matplotlib.

Historian parameters list

• P : proportionnal part
• I : integral part
• D : derivative part
• ERROR : PID error
• SETPOINT : PID setpoint
• PROCESS_VALUE : PID process value
• OUTPUT : PID output

The maximum lenght of the historian can be choose. By default it is set to 100 000 record per parameter. Take care about your memory.

In example for one parameters. A float value take 24 bytes in memory. So 100 000 floats take 2 400 000 bytes (~2.3MB).

For all parameters it takes 16 800 000 bytes (~16MB). It's not big for a computer, but if PID is executed each millisecond (0.001s), 100 000 record represent only 100 seconds of recording.

If you want to save 1 hour at 1 millisecond you will need 3 600 000 records (~82.4MB) for one parameter, and for all parameters it will takes ~576.8MB.

For a raspberry pi 3 B+ it's the half of the RAM capacity (1GB)

Integral limitation

The integral part of the PID can be limit to avoid overshoot of the output when the error is too high (When the setpoint variation is too high, or when the system have trouble to reach setpoint).

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, integralLimit = 20.0)

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the integral part of the PID is clamped between -20 and 20.

Manual mode

The PID can be switch in manual mode, this allow to operate output directly through manualValue.

from PID_Py.PID import PID

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0)

...

# Manual mode
pid.manualMode = True
pid.manualValue = 12.7

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, command will be always equal to 12.7. The PID calculation is no longer executed. The proportionnal, integral and derivative parts still at the same value to avoid bump when switching back to automatic.

To avoid bump when switching in manual there is bumplessSwitching attribute. This attributes keep manualValue equal to output.

If you disable this function you will have bump when you switch in manual mode with manualValue different of output. If this case you can destabilise (:heavy_exclamation_mark:) your system. Be careful

Logging

The PID can use a logger (logging.Logger built-in class) to log event. Logging configuration can be set outside of the PID. See logging.Logger documentation.

from PID_Py.PID import PID
import logging

# Initialization
pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, logger = logging.getLogger("PID"))

...

# PID execution (call it as fast as you can)
command = pid(processValue = feedback, setpoint = targetValue)

In the example above, the PID will send event on the logger. The logger can also get with the name.

pid = PID(kp = 0.0, ki = 0.0, kd = 0.0, logger = "PID")

Threaded PID

With the threaded PID you don't have to call pid(processValue, setpoint). It's call as fast as possible or with a constant cycle time. When you want to stop the PID use quit attribute to finish the current execution and exit.

from PID_Py.PID import ThreadedPID

# Initialization
pid = ThreadedPID(kp = 0.0, ki = 0.0, kd = 0.0, cycleTime = 0.01)
pid.start()

...

# PID inputs
pid.setpoint = targetValue
pid.processValue = feedback

# PID output
command = pid.output

...

# Stop PID
pid.quit = True
pid.join()

In the example above the threaded PID is created with 10ms (0.01s) of cyclic time. It means that the calculation is executed each 10ms.