a10-octavia 0.1.0.dev384

A10 Octavia Provider Driver

A10 Networks OpenStack Octavia Driver

Table of Contents

1. Overview

2. System Requirements

3. Setup and Configuration

   1. For use with vThunders

   2. For use with hardware devices

4. Setting Object Defaults

5. Troubleshooting

6. Contributing

7. Issues and Inquiries

Overview

This solution is currently in beta stage with limited support

The A10 Networks Octavia Driver allows for configuration of Thunder, vThunder, and AX Series Appliances deployed in an Openstack enviroment. While the default Octavia provider leverages an "Amphora per VIP" architecture, this provider driver uses a "Thunder per Tenant" architecture. Therefore, each tenant may only be serviced by a single active Thunder device.

System Requirements

Openstack Controller Node Minimum Requirements

• Memory: 8GB
• Disk: 20GB
• OS: Ubuntu 18.04 or later
• OpenStack (Nova, Neutron, Etc): Stein Release
• Octavia version: >=4.1.1, <5.0.0.0rc1 (Stein versions)

Openstack Compute Node Minimum Requirements

• vCPUs: 8
• Memory: 16GB
• Disk: 40GB
• OS: Ubuntu 18.04 or later
• Openstack (Nova, Neutron, Etc): Stein Release

ACOS Device Requirements

• ACOS version: ACOS 4.1.4 GR1 P2
• AXAPI version: 3.0

Installation

This guide assumes that Openstack has already been deployed and Octavia has already been configured.

Note: The following configurations should be done as an Openstack admin user

Install from PyPi

$ pip install a10-octavia

Setup And Configuration

1. Enable A10 provider driver in Octavia config file

Add the following to /etc/octavia/octavia.conf under the api-settings section

enabled_provider_drivers = a10: 'The A10 Octavia driver.'

default_provider_driver = a10

2. Restart Openstack Octavia services

Use systemctl or similar a command to restart the Octavia API service.

3a. For use with vThunders

3aa. Upload vThunder image and create a nova flavor for amphorae devices

Upload a vThunder image (QCOW2) and create a nova flavor with the required resources.

Recommended vThunder flavor settings:

• 8 vCPUs
• 8GB RAM
• 30GB disk

$ openstack image create --disk-format qcow2 --container-format bare --public --file vThunder414.qcow2 vThunder.qcow2
$ openstack flavor create --vcpu 8 --ram 8196 --disk 30 vThunder_flavor

Note down the image ID and flavor ID of created resources.

Please contact [e-mail] for questions on acquiring and licensing vThunder images

3ab. Create the a10-octavia.conf file

$ mkdir /etc/a10
$ touch /etc/a10/a10-octavia.conf

Note: Make sure the user running the Octavia service has access to these files

3ac. Sample a10-octavia.conf for vThunders

[VTHUNDER]
DEFAULT_VTHUNDER_USERNAME = "admin"
DEFAULT_VTHUNDER_PASSWORD = "a10"
DEFAULT_AXAPI_VERSION = "30"

[a10_controller_worker]
amp_image_owner_id = <admin_project_id>
amp_secgroup_list = <security_group_to_apply>
amp_flavor_id = <vthunder_flavor_id>
amp_boot_network_list = <netword_id_to_boot_vthunder_in_admin_project>
amp_ssh_key_name = <ssh_key_for_amphorae>
network_driver = a10_octavia_neutron_driver
workers = 2
amp_active_retries = 100
amp_active_wait_sec = 2
amp_image_id = <vthunder_image_id>
loadbalancer_topology = <SINGLE or ACTIVE_STANDBY>

[a10_health_manager]
udp_server_ip_address = <server_ip_address_for_health_monitor>
bind_port = 5550
bind_ip = <controller_ip_configured_to_listen_for_udp_health_packets>
heartbeat_interval = 5
heartbeat_key = insecure
heartbeat_timeout = 90
health_check_interval = 3
failover_timeout = 600
health_check_timeout = 3
health_check_max_retries = 5

[a10_house_keeping]
load_balancer_expiry_age = 3600
amphorae_expiry_age = 3600

Full list of options can be found here: Config Options Module

3ad. Update security group to access vThunder AXAPIs

These settings are for ports allocated on the managment network. It's up to the operator to define the data network security rules.

When delopying with the STANDALONE loadbalancer topology

Protocol	Port	Ingress	Egress	Purpose
TCP	80	✓	✓	Communication with AXAPI
TCP	443	✓	✓	Communication with AXAPI
UDP	5550		✓	Communication with Health Manager Service

When deploying with the ACTIVE-STANDBY loadbalancer topology

Protocol	Port	Ingress	Egress	Purpose
TCP	80	✓	✓	Communication with AXAPI
TCP	443	✓	✓	Communication with AXAPI
UDP	ALL	✓	✓	For specifics contact [e-mail]

3b. For use with hardware devices

3ba. Create the a10-octavia.conf file

$ mkdir /etc/a10
$ touch a10-octavia.conf

3bb. Sample a10-octavia.conf for hardware devices

[a10_controller_worker]
amp_secgroup_list = <security_group_to_apply> 
amp_boot_network_list = <netword_id_to_boot_amphorae_in_admin_project>
amp_ssh_key_name = <ssh_key_for_amphorae>
network_driver = a10_octavia_neutron_driver
workers = 2
amp_active_retries = 100
amp_active_wait_sec = 2
loadbalancer_topology = SINGLE

[RACK_VTHUNDER]
devices = """[
                    {
                     "project_id":"<project_id>",
                     "ip_address":"10.0.0.4",
                     "undercloud":"True",
                     "username":"<username>",
                     "password":"<password>",
                     "device_name":"<device_name>",
                     "axapi_version":"30"
                     },
                     {
                     "project_id":"<another_project_id>",
                     "ip_address":"10.0.0.5",
                     "undercloud":"True",
                     "username":"<username>",
                     "password":"<password>",
                     "device_name":"<device_name>",
                     "axapi_version":"30",
                     }
             ]
       """

Full list of options can be found here: Config Options Module

4. Run database migrations

From the /path/to/a10-octavia/a10_octavia/db/migration folder run

$ alembic upgrade head

If versioning error occurs, delete all entries in the alembic_version table from octavia database and re-run the above command.

mysql> use octavia;
mysql> DELETE FROM alembic_version;

Note: Octavia verisons less than 4.1.1 have the alembic_migrations table instead

5. Register and start a10-octavia services

With a10-octavia installed, run the following command to register the services

$ install-a10-octavia

This will install systemd services with names - a10-controller-worker.service, a10-health-manager.service and a10-housekeeper-manager.service.

5a. Make sure the services are up and running.

$ systemctl status a10-controller-worker.service a10-health-manager.service a10-housekeeper-manager.service

You can start/stop the services using systemctl/service commands.

Setting Object Defaults

These settings are added to the a10-octavia.conf file. They allow the operator to configure options not exposed by the Openstack CLI.

WARNING: Any option specified here will apply globally meaning all projects and devices

Loadbalancer/virtual server config example

[SLB]
arp_disable = False
default_virtual_server_vrid = "10"
logging_template = "Logging_temp1"
policy_template = "policy_temp1"
template_virtual_server = "virtual_server_template1"
default_virtual_server_vrid = 0

Listener/virtual port config example

[LISTENER]
ipinip = False
no_dest_nat = False
ha_conn_mirror = False
template_virtual_port = "vport_template"
template_tcp = "tcp_template"
template_policy = "policy_temp1"
autosnat = True
conn_limit = 5000
template_http = "http_template"

Pool/service group config example

[SERVICE - GROUP]
templates = "server1"

Member config example

[SERVER]
conn_limit = 5000
conn_resume = 1
templates = "server1"

Full list of options can be found here: Config Options Module

Troubleshooting

You may check logs of the services using journalctl commands. For example:

$ journalctl -af --unit a10-controller-worker.service
$ journalctl -af --unit a10-health-manager.service
$ journalctl -af --unit a10-housekeeper-manager.service

Contributing

1. Fork the a10-octavia repository

How To Fork

2. Clone the repo from your fork

$ git clone https://[e-mail]:<username>/a10-octavia.git

3. Checkout to a new branch

$ git checkout -b feature/<branch_name>

4. Run octavia install script

WARNING: THIS INSTALLS DEVSTACK. RUN IN A VM

Run the following as the super user

$ sudo ./path/to/a10-octavia/a10_octavia/contrib/devstack/new-octavia-devstack.sh

5. Become the stack user and move the a10-octavia repo

$ sudo su - stack
$ mv /path/to/a10-octavia .
$ sudo chown -R stack:stack a10-octavia

6. Install in edit mode

$ pip install -e a10-octavia

7. Restart the Octavia API service

sudo systemctl restart [e-mail]

8. Update security groups

Modify the lb-mgmt-sec-grp to includ

Protocol	Port	Ingress	Egress	Purpose
TCP	80	✓	✓	Communication with AXAPI
TCP	443	✓	✓	Communication with AXAPI
UDP	ALL	✓	✓	For specifics contact [e-mail]

Modify the lb-health-mgr-sec-grp to include

Protocol	Port	Ingress	Egress	Purpose
UDP	5550		✓	Communication with Health Manager Service

9. Register and start the a10-octavia services

$ install-a10-octavia

Testing install script changes

When testing changes to the install-a10-octavia script, run python setup.py install from within the a10-octavia dir to re-install the script.

Issues and Inquiries

For all issues, please send an email to [e-mail]

For general inquiries, please send an email to [e-mail]