alchemy-logging 1.0.1

A wrapper around the logging package to provide Alchemy Logging functionality

Alchemy Logging (alog) - Python

The alog framework provides tunable logging with easy-to-use defaults and power-user capabilities. The mantra of alog is "Log Early And Often". To accomplish this goal, alog makes it easy to enable verbose logging at develop/debug time and trim the verbosity at production run time.

Setup

To use the alog module, simply install it with pip:

pip install alchemy-logging

Channels and Levels

The primary components of the framework are channels and levels which allow for each log statement to be enabled or disabled when appropriate.

1. Levels: Each logging statement is made at a specific level. Levels provide sequential granularity, allowing detailed debugging statements to be placed in the code without clogging up the logs at runtime. The sequence of levels and their general usage is as follows:

   1. off: Disable the given channel completely
   2. fatal: A fatal error has occurred. Any behavior after this statement should be regarded as undefined.
   3. error: An unrecoverable error has occurred. Any behavior after this statement should be regarded as undefined unless the error is explicitly handled.
   4. warning: A recoverable error condition has come up that the service maintainer should be aware of.
   5. info: High-level information that is valuable at runtime under moderate load.
   6. trace: Used to log begin/end of functions for debugging code paths.
   7. debug: High-level debugging statements such as function parameters.
   8. debug1: High-level debugging statements.
   9. debug2: Mid-level debugging statements such as computed values.
   10. debug3: Low-level debugging statements such as computed values inside loops.
   11. debug4: Ultra-low-level debugging statements such as data dumps and/or statements inside multiple nested loops.

2. Channels: Each logging statement is made to a specific channel. Channels are independent of one another and allow for logical grouping of log messages by functionality. A channel can be any string. A channel may have a specific level assigned to it, or it may use the configured default level if it is not given a specific level filter.

Using this combination of Channels and Levels, you can fine-tune what log statements are enabled when you run your application under different circumstances.

Usage

Configuration

import alog

if __name__ == "__main__":
    alog.configure(default_level="info", filters="FOO:debug,BAR:off")

In this example, the channel "FOO" is set to the debug level, the channel "BAR" is fully disabled, and all other channels are set to use the INFO level.

In addition to the above, the configure function also supports the following arguments:

• formatter: May be "pretty", "json", or any class derived from AlogFormatterBase
• thread_id: Bool indicating whether or not to include a unique thread ID with the logging header (pretty) or structure (json).
• handler_generator: This allows users to provide their own output handlers and replace the standard handler that sends log messages to stderr.

Logging Functions

For each log level, there are two functions you can use to create log lines: The standard logging package function (with additional functions for higher debug levels), or the corresponding alog.<level> function. The former will always log to the MAIN channel while the later requires that a channel string be specified.

import alog
import logging

def foo(age):
    alog.use_channel("FOO").debug3(
        "Debug3 line on the FOO channel with an int value %d!", age
    )
    logging.debug("debug line on the MAIN channel")

Channel Log

In a given portion of code, it often makes sense to have a common channel that is used by many logging statements. Re-typing the channel name can be cumbersome and error-prone, so the concept of the Channel Log helps to eliminate this issue. To create a Channel Log, call the use_channel function. This gives you a handle to a channel log which has all of the same standard log functions as the top-level alog, but without the requirement to specify a channel. For example:

import alog

log = alog.use_channel("FOO")

def foo(age):
    log.info("Hello Logging World! I am %d years old", age)

NOTE: In this (python) implementation, this is simply a wrapper around logging.getLogger()

Log Contexts

One of the most common uses for logging is to note events when a certain block of code executes. To facilitate this, alog has the concept of log contexts. The two primary contexts that alog supports are:

• ContextLog: This contextmanager logs a START: message when the context starts and an END: message when the context ends. All messages produced within the same thread inside of the context will have an incremented level of indentation.

import alog

alog.configure("debug2")
log = alog.use_channel("DEMO")

with alog.ContextLog(log.info, "Doing some work"):
    log.debug("Deep in the muck!")

2021-07-29T19:09:03.819422 [DEMO :INFO] BEGIN: Doing some work
2021-07-29T19:09:03.820079 [DEMO :DBUG]   Deep in the muck!
2021-07-29T19:09:03.820178 [DEMO :INFO] END: Doing some work

• ContextTimer: This contextmanager starts a timer when the context begins and logs a message with the duration when the context ends.

import alog
import time

alog.configure("debug2")
log = alog.use_channel("DEMO")

with alog.ContextTimer(log.info, "Slow work finished in: "):
    log.debug("Starting the slow work")
    time.sleep(1)

2021-07-29T19:12:00.887949 [DEMO :DBUG] Starting the slow work
2021-07-29T19:12:01.890839 [DEMO :INFO] Slow work finished in: 0:00:01.002793

Function Decorators

In addition to arbitrary blocks of code that you may wish to scope or time, a very common use case for logging contexts is to provide function tracing. To this end, alog provides two useful function decorators:

• @logged_function: This decorator wraps the ContextLog and provides a START/END scope where the message is prepopulated with the name of the function.

import alog

alog.configure("debug")
log = alog.use_channel("DEMO")

@alog.logged_function(log.trace)
def foo():
    log.debug("This is a test")

foo()

2021-07-29T19:16:40.036119 [DEMO :TRCE] BEGIN: foo()
2021-07-29T19:16:40.036807 [DEMO :DBUG]   This is a test
2021-07-29T19:16:40.036915 [DEMO :TRCE] END: foo()

• @timed_function: This decorator wraps the ContextTimer and performs a scoped timer on the entire function.

import alog
import time

alog.configure("debug")
log = alog.use_channel("DEMO")

@alog.timed_function(log.trace)
def foo():
    log.debug("This is a test")
    time.sleep(1)

foo()

2021-07-29T19:19:47.468428 [DEMO :DBUG] This is a test
2021-07-29T19:19:48.471788 [DEMO :TRCE] 0:00:01.003284