aurt 0.0.4

A robot dynamic parameters calibration toolbox.

Aarhus University Robotics Toolbox (AURT) Overview

Installation

To install the tool, type:

pip install aurt

or, if plotting and visualization features are needed,

pip install aurt[vis]

Command Line Interface

The following shows the different use cases that aurt supports. In order to improve performance, the model is compiled in different stages, in a way that allows the user to try alternative joint dynamics models without having to re-create the full model, which is a computationally demanding procedure.

Compile Rigid Body Dynamics Model

aurt compile-rbd --mdh mdh.csv --out rigid_body_dynamics

Reads the Modified Denavit-Hartenberg (MDH) parameters in file mdh.csv and outputs rigid-body dynamics model to file rigid_body_dynamics. The generated model does not include the joint dynamics. To visualize the kinematics of the robot, make sure the roboticstoolbox-python is installed, and add the argument --plot to the compile-rbd command.

Compile Robot Dynamics Model

aurt compile-rd --model-rbd rigid_body_dynamics --friction-torque-model square --friction-viscous-powers 2 1 4 --out robot_dynamics

Reads the rigid-body dynamics model created with the compile-rbd command, and generates the robot dynamics model, taking into account the joint dynamics configuration.

The friction configuration options are:

• --friction-torque-model TYPE where TYPE in {none, square, absolute} are depicted in the figure below for, respectively, parts (a), (b), and (c).

• --friction-viscous-powers POWERS where POWERS is a set of integers having the format P1 P2 ... used to define the odd polynomial function in the angular velocity of any joint as

  

  with the viscous coefficient of friction corresponding to the integer element of , if is even and otherwise.

Calibrate

aurt calibrate --model robot_dynamics --data measured_data.csv --gravity 0 0 -9.81 --out-params calibrated_parameters.csv --out-calibrated-model rd_calibrated --plot

Reads; 1) the model produced by the compile-rd command, 2) the measured data in measured_data.csv, and 3) the gravity components GX GY GZ and writes; 1) the values of the calibrated base parameters to calibrated_parameters.csv and 2) the calibrated robot dynamics model to rd_calibrated. The gravity vector determines the orientation of the robot base for which the parameters will be calibrated. For showing the calibration plot, use the argument --plot.

The measured data should contain the following fields:

• timestamp of type float, representing the number of seconds passed from a given reference point.
• target_qd_j of type float, representing the jth joint target angular velocity, as computed by the robot controller, where j is an integer in {0, 1, ..., N}.
• actual_q_j of type float, representing the jth joint angle, as measured by the robot controller, where j is an integer in {0, 1, ..., N}.
• actual_current_j of type float, representing the jth joint current, as measured by the robot controller, where j is an integer in {0, 1, ..., N}.

Predict

aurt predict --model rd_calibrated --data measured_data.csv --gravity 0 0 -9.81 --out predicted_output.csv

Reads; 1) the model produced by the calibrate command, 2) the measured data in measured_data.csv, and 3) the gravity components GX GY GZ, and writes the predicted output to predicted_output.csv.

The prediction fields are:

• timestamp of type float, referring to the time of the measured data, as in Calibrate.
• predicted_current_j of type float, representing the jth joint current, as predicted by the robot model, where j is an integer in {0, 1, ..., N}.

Calibrate and Validate

aurt calibrate-validate --model robot_dynamics --data measured_data.csv --gravity 0 0 -9.81 --calibration-data-rel FRACTION --out-params calibrated_parameters.csv --out-calibrated-model rd_calibrated --out-prediction predicted_output.csv --plot

Simultaneously calibrates and validates the robot dynamics model using the dataset measured_data.csv. The command implements the functionalities of the commands calibrate and predict. The data of measured_data.csv is separated into two consecutive parts 1) calibration data and 2) validation data. The calibration data has a duration of 0.1 < FRACTION < 0.9 times the duration of measured_data.csv while the remaining part of the data is used for validation.

Contributing

Development environment

To setup the development environment:

1. Open terminal in the current folder.
2. Install all packages for development: pip install -e .[vis].
3. Unpack the datasets (see Dataset management)
4. To run all non live tests, open a command prompt or powershell in the repository root, and run python build.py --run-tests all-non-live. If you are using Linux, use python3 instead of python.

NOTE: Run tests before commits. If they don't pass, fix them before committing.

Publishing this package on pypi

1. Update version in setup.py
2. Make sure all tests, except the live ones, are passing.
3. Delete folders dist build if they exist.
4. Activate virtual environment.
5. Install twine and wheel: pip install twine wheel
6. Create a source distribution: python setup.py sdist
7. Create the binary distribution: python setup.py bdist_wheel
8. Upload distribution to PyPI: python -m twine upload dist/*
9. When asked for username and password, use the token and password created with your PyPI account.

Dataset management

Small dataset (< 100MB compressed)

If the data is small, then:

• Each round of experiments should be placed in a folder with an informative name, inside the Dataset folder.
• There should be a readme file in there explaining the steps to reproduce the experiment, parameters, etc...
• The csv files should be 7ziped and committed. Do not commit the csv file.
• There should be tests that use the data there.

Large Datasets (>= 100MB compressed)

If the data is large, then:

• A "lite" version of the dataset should be in the dataset folder (following the same guidelines as before)
  • This is important to run the tests.
• the larger version should be placed in the shared drive (see below).

There is a shared drive for large datasets. The shared drive Nat_robot-datasets has been created with Emil Madsen as owner.

Shared Drive	Owner	E-mail	Department
Nat_robot-datasets	au504769 (Emil Madsen)	[e-mail]	Electrical and Computer Engineering (ECE)

Read/write access is assigned to:

Username	Name	E-mail	Department
au602135	Cláudio Ângelo Gonçalves Gomes	[e-mail]	Electrical and Computer Engineering (ECE)
au522101	Christian Møldrup Legaard	[e-mail]	Electrical and Computer Engineering (ECE)
au513437	Daniella Tola	[e-mail]	Electrical and Computer Engineering (ECE)

For more information on access, self-service and management of files: https://medarbejdere.au.dk/en/administration/it/guides/datastorage/data-storage/