hcsr04sensor 1.5.3

Module to access the HCSR04 sensor on a Raspberry Pi

HC-SR04 Ultrasonic Sensor on Raspberry Pi
=========================================


[Hcsr04sensor Web Page](https://www.linuxnorth.org/hcsr04sensor)


Calculate distance and depth measurements with an HCSR04 Ultrasonic Sound Sensor and a Raspberry Pi. Instructions assume that you are using Raspbian Linux.

This module also works with the JSN-SR04T waterproof sound sensor.


Python2 Install
===============


sudo apt-get install python-pip
sudo pip install hcsr04sensor


Python3 Install
===============

sudo apt-get install python3-pip
sudo pip3 install hcsr04sensor


Description
===========
The module does the following;

* Returns an error corrected distance by using the median reading of a sorted
sample. NOTE - The default sample size is 11 readings.

You can specify a
different sample size by passing sample_size=x to raw_distance (where x is your desired
number of readings). This is useful if you need to lower the sample size to take
quicker readings. Beware that the probability of getting erroneous readings
increases as sample size is reduced. For my purposes a sample of 11 readings gives a consistent
value that I can trust and takes approximately 3 seconds to run with a 0.1
second wait time between individual samples.

It is also possible to speed up the readings by passing a lower value to
sample_wait in raw_distance.

The lower the value the quicker the invidual
samples will be taken. A default of 0.1 is a safe wait time but this can be
reduced further. CPU usage increases as faster readings are taken as well as
the chance for errors.

This module uses BCM pin values. See the Raspberry Pi pin layout documentation for your model.

* Rounds the value to a specified decimal place.

* Uses BCM pin values by default. BOARD pin values are supported.

* Adjusts the reading based on temperature by adjusting the speed of sound.

* Allows measuring distance and depth in metric and imperial units. See;

pydoc hcsr04sensor.sensor

* Raises an exception if a faulty cable or sensor prevents an echo pulse from being received.

Accuracy of Readings
====================

If you need highly accurate readings then this module would not be suitable for your project. In that case you should probably use an Arduino instead of a Raspberry Pi.

Linux is not a Real Time OS so you can expect to get a small variance on each reading, usually within a half cm of the actual value. I say "usually" because every once in a while you can get a reading that is way out of range. This is due to the OS executing other tasks before getting your distance reading. It is why I use a sample of readings. I can always trust that the median of my sample of 11 readings is good.

Highly accurate readings are not required for some applications, for example I use this module in an application I wrote for a sump pump monitor. I am not worried about millimeter accuracy for that application. 1 cm variance on a meter deep pit is close enough to alert me to problems.


Distance Limitations
====================

The HCSR04 sensor is suited for short distance readings. The specification manual says it is suitable up to 13 feet. I have tested it to go further than that, but anything over 12 feet starts having periodic strange readings.
This module is not suitable for long distances.


Usage
=====

See example scripts in https://github.com/alaudet/hcsr04sensor/tree/master/recipes

Access to Raspberry Pi GPIO pins require elevated priviledges if using version 0.5.11 of RPi.GPIO. Run example
scripts with sudo.

Testing the Module
==================

Added a script that is installed to /usr/local/bin called hcsr04.py.
This utility does not presently support BOARD pin values. Use BCM pin values.

usage: hcsr04.py [-h] -t TRIG -e ECHO [-sp SPEED] [-ss SAMPLES]

Script tests the HCSR04 sensor under different configurations

optional arguments:
-h, --help show this help message and exit
-t TRIG, --trig TRIG Trig Pin (Required - must be an integer, must use
BCM pin values)
-e ECHO, --echo ECHO Echo Pin (Required - must be an integer, must use
BCM pin values)
-sp SPEED, --speed SPEED
Time between individual reading samples (Optional -
must be a float, default is 0.1 seconds)
-ss SAMPLES, --samples SAMPLES
Reading Sample Size (Optional - must be an integer, default is
11)


Take a Basic Reading
=====================

If you don't want to use a sample of readings for error handling, warnings or pin cleanups I have included a stand alone function that will return a basic metric reading
without creating a Measurement object. It returns the exact one-time reading that is provided by the sensor and Rpi.GPIO. This allows you to handle all of these things to your own preference in your codei.

See the example basic_reading.py script in https://github.com/alaudet/hcsr04sensor/tree/master/recipes


Recommended
===========

To upgrade to version 0.6.x of RPi.GPIO which does not require elevated priviledges you can simply upgrade as follows;

Note: On Raspbian Wheezy you still seem to have to run RPi.GPIO with sudo in version 6. It works without sudo in
Rasbian Jessie which is the latest version of Raspbian.

For Python 2

sudo pip install -U hcsr04sensor

or

sudo apt-get upgrade python-rpi.gpio




For Python 3

sudo pip3 install -U hcsr04sensor

or

sudo apt-get upgrade python3-rpi.gpio

Contributing
============

Contributions to hcsr04sensor are welcome. Please open an issue in the issue
tracker prior to a pull request.

New features and bug fixes should be applied against the devel branch and not master. Contributions against the master branch will be rejected.

Nose is currently used for testing. All tests should pass before issuing
the pull request.


Donate
======

[Your Donation is Appreciated](https://www.linuxnorth.org/donate/)