max-ble-hci 1.2.3

BLE HCI Test interface for controllers capable of the UART transport

MAX-BLE-HCI

Python3 BLE HCI over serial Directed to MAX Vendor Specific Commands

Read the Docs

Insatll from PyPi

MAX-BLE-HCI is hosted via PyPi and can be installed with the following command

pip install max-ble-hci

Installation from source

If you prefer to use the most up to date version, you can also install from source.

The intsall.sh or .bat are used to install the library into your Python site packages and be done as such.
On Linux or MacOS

sudo chmod +x install.sh
./install.sh

On Windows

install.bat

Basic Usage

The BLE-HCI is a mostly generic library, which is capable of driving any BLE devices which can communicate using the UART transport.

To use with Analog Devices, Inc. BLE capable MAX32 microcontrollers, please flash one of the following examples to the chip you are using

• MAX32655
• MAX32665
• MAX32690

If you have not yet set up an installation of the Analog-Devices-MSDK, please follow the instructions found here https://github.com/Analog-Devices-MSDK/msdk/tree/main
Once the board is flashed refer to the README in the example to configure your board.

Locate the serial port to which the HCI is connected to. If for example, your serial port is COM5, the following code would be used to reset the device.

from max_ble_hci import BleHci

port_name = "COM5"

hci = BleHci(port_name)
hci.reset()

Command Line Interface (CLI)

By defaults, the CLI capable of driving the BLE-HCI is installed as part of the package and can be accessed by running

max_ble_hci --version

The cli requires a serial port to connect the HCI to and is passed in through the command line. Once connected, you can type the help command as such, and begin to explore the CLI.

>>> help
usage:  [-h]
        {clear,cls,addr,memstats,adv,scan,init,data-len,send-acl,sink-acl,conn-stats,cs,test-stats,ts,bben,bbdis,rssi,reset,tx-test,tx,txtestvs,txvs,rx-test,rx,rx-test-vs,rxvs,end-test,end,reset_ts,rsts,tx-power,txp,discon,dc,set-chmap,cmd,exit,quit,q,help,h}
        ...

positional arguments:
  {clear,cls,addr,memstats,adv,scan,init,data-len,send-acl,sink-acl,conn-stats,cs,test-stats,ts,bben,bbdis,rssi,reset,tx-test,tx,txtestvs,txvs,rx-test,rx,rx-test-vs,rxvs,end-test,end,reset_ts,rsts,tx-power,txp,discon,dc,set-chmap,cmd,exit,quit,q,help,h}
    clear (cls)         Clear the scrren
    addr                Set the device address.
    memstats            Get BLE stack memory usage statistics
    adv                 Send the advertising commands
    scan                Send scanning commands and print scan reports, ctrl-c to exit.
    init                Send the initiating commands to open a connection
    data-len            Set the max data length
    send-acl            Send ACL packets
    sink-acl            Sink ACL packets, do not send events to host
    conn-stats (cs)     Get the connection stats
    test-stats (ts)     Get the test stats
    bben                Enable the Baseband Radio (Required for RSSI capture)
    bbdis               Disable the Baseband Radio
    rssi                Get an RSSI sample using CCA
    reset               Sends an HCI reset command
    tx-test (tx)        Execute the transmitter test.
    txtestvs (txvs)     Execute the vendor-specific transmitter test
    rx-test (rx)        Execute the receiver test
    rx-test-vs (rxvs)   Execute the vendor-specific receiver test
    end-test (end)      End the Tx/Rx test, print the number of correctly received packets
    reset-ts (rsts)     Reset accumulated stats from DTM
    tx-power (txp)      Set the Tx power
    discon (dc)         Send the command to disconnect
    set-chmap           Set the connection channel map to a given channel.
    cmd                 Send raw HCI command
    exit (quit, q)      Exit the program
    help (h)            Show help message

options:
  -h, --help            show this help message and exit
>>> 

Contributing

Contributions are encouraged! Pull requests must pass all GitHub Actions unless directly waved by an admin of the repository.

Python Versioning

This package is designed to support Python 3.8 and up. Non backwards compatible features will not be accepted (ex Use of match which was introduced in 3.10)

Style Guidlines

MAX-BLE-HCI is formatted using the Black formatter. It can be installed via pip using pip install black