pa-dlna 0.13

Forward pulseaudio streams to DLNA devices.

pa-dlna forwards audio streams to DLNA devices.

A Python project based on asyncio, that uses ctypes to interface with the libpulse library and supports the PulseAudio and PipeWire [1] sound servers.

pa-dlna is composed of the following components:

• The pa-dlna program forwards PulseAudio streams to DLNA devices.

• The upnp-cmd is an interactive command line tool for introspection and control of UPnP devices [2].

• The UPnP Python sub-package is used by both commands.

See the pa-dlna documentation.

Requirements

Python version 3.8 or more recent.

psutil

The UPnP sub-package and therefore the upnp-cmd and pa-dlna commands depend on the psutil Python package. This package is available in most distributions as python3-psutil or python-psutil. It will be installed by pip as a dependency of pa-dlna if not already installed as a package of the distribution.

libpulse

libpulse is a Python asyncio interface to the Pulseaudio and Pipewire libpulse library. It was a sub-package of pa-dlna and has become a full-fledged package on PyPi. It will be installed by pip as a dependency of pa-dlna.

parec

pa-dlna uses the pulseaudio parec program [3]. Depending on the linux distribution it may be already installed as a dependency of pulseaudio or of pipewire-pulse. If not, then the package that owns parec must be installed. On archlinux the package name is libpulse, on debian it is pulseaudio-utils.

Encoders

No other dependency is required by pa-dlna when the DLNA devices support raw PCM L16 (RFC 2586) [4].

Optionally, encoders compatible with the audio mime types supported by the devices may be used. pa-dlna currently supports the ffmpeg (mp3, wav, aiff, flac, opus, vorbis, aac), the flac and the lame (mp3) encoders. The list of supported encoders, whether they are available on this host and their options, is printed by the command that prints the default configuration:

$ pa-dlna --dump-default

pavucontrol

Optionally, one may install the pavucontrol package for easier management of associations between sound sources and DLNA devices.

Installation

pipewire as a pulseaudio sound server

The pipewire, pipewire-pulse and wireplumber packages must be installed and the corresponding programs started. If you are switching from pulseaudio, make sure to remove /etc/pulse/client.conf or to comment out the setting of default-server in this file as pulseaudio and pipewire do not use the same unix socket path name.

The parec ‘s package includes the pactl program. One may check that the installation of pipewire as a pulseaudio sound server is successfull by running the command:

$ pactl info

pa-dlna

Install pa-dlna with pip:

$ python -m pip install pa-dlna

Configuration

A pa-dlna.conf user configuration file overriding the default configuration may be used to:

• Change the preferred encoders ordered list used to select an encoder.

• Configure encoder options.

• Set an encoder for a given device and configure the options for this device.

• Configure the sample_format, rate and channels parameters of the parec program used to forward PulseAudio streams, for a specific device, for an encoder type or for all devices.

See the configuration section of the pa-dlna documentation.

[1]

When using PipeWire with the Wireplumber session manager, pa-dlna must be started before the audio streams that are routed to DLNA devices. Re-starting those audio streams fixes the problem. See pa-dlna issue 15 and Wireplumber issue 511.

[2]

The pa-dlna and upnp-cmd programs can be run simultaneously.

[3]

The parec program also uses the libpulse library which is included in parec ‘s package or is installed as a dependency. Note also that this package includes the pactl and pacmd programs.

[4]

DLNA devices must support the HTTP GET transfer protocol and must support HTTP 1.1 as specified by Annex A.1 of the ConnectionManager:3 Service UPnP specification.