pairLiftOver 0.2.0

Convert genomic coordinates of contact pairs from one assembly to another.

pairLiftOver

pairLiftOver is a Python package that converts the two-dimensional genomic coordinates of chromatin contact pairs between assemblies.

pairLiftOver is based on the UCSC chain files. It takes a pairs file or matrix file as input, performs coordinate conversion for each contact pair, and outputs a sorted pairs file or contact matrix with coordinates in another assembly.

Installation

pairLiftOver and all the dependencies can be installed through either conda or pip:

$ conda config --add channels defaults
$ conda config --add channels bioconda
$ conda config --add channels conda-forge
$ conda create -n pairliftover pairtools cooler kerneltree
$ conda activate pairliftover
$ pip install pairLiftOver hic-straw

Data Format

Currently, pairLiftOver supports 4 input data formats: 4DN pairs, allValidPairs, cool, and hic. It is necessary to provide a pairs file (4DN pairs or allValidPairs) to get the most accurate results, however, when such file is not available, pairLiftOver can also operate on contact matrices binned at kilobase resolutions (in cool or hic formats). For hic format, since multiple matrices at various resolutions are stored in a single file, pairLiftOver automatically detects and reads data from the one at the highest resolution.

The default output of pairLiftOver is a sorted pairs file in the standard 4DN pairs format, containing seven columns: “readID”, “chr1”, “pos1”, “chr2”, “pos2”, “strand1”, and “strand2”. However, you can also choose to output a matrix file in cool or hic format by setting the parameter --output-format.

Usage

Open a terminal, type pairLiftOver -h for help information.

Here is an example command which uses a 4DN pairs file in hg19 coordinates as input, and outputs an mcool file with chromatin contacts in hg38 coordinates:

$ pairLiftOver --input test.hg19.pairs.gz --input-format pairs --out-pre test-hg38 \
--output-format cool --out-chromsizes hg38.chrom.sizes --in-assembly hg19 --out-assembly hg38 \
--logFile pairLiftOver.log

Since the version 0.1.3, pairLiftOver has added a function to perform a pure format conversion. For example, the following command transforms a contact matrix from the .cool format to the .hic format, without the coordinate liftover. Note that the values of --in-assembly and --out-assembly need to be the same to turn on this function:

$ pairLiftOver --input Rao2014-K562-MboI-allreps-filtered.5kb.cool --input-format cooler \
--out-pre K562-format-conversion-test --output-format hic --out-chromsizes hg19.chrom.sizes \
--in-assembly hg19 --out-assembly hg19 --memory 40G

Running time and memory usage

The running time of pairLiftOver grows linearly with the number of contact pairs. The memory usage can be roughly controlled by the parameter --memory. In the figure below, pairLiftOver was tested on the downsampled GM12878 Hi-C datasets (Rao 2014) (ranging from 100 million to 1 billion valid pairs). For each run, the memory and the number of processes allocated to pairLiftOver were set to 8Gb (--memory 8G) and 8 (--nproc 8), respectively.

Accuracy

So far, pairLiftOver has been tested on datasets of human (Rao 2014, GM12878 and K562), mouse (Rao 2014, CH12-LX) and zebrafish (Yang 2020, brain tissue). And the matrices obtained by pairLiftOver are nearly identical to the re-mapping results at various resolutions.

Citation

Wang, X., Luan, Y., Yue, F. EagleC: A deep-learning framework for detecting a full range of structural variations from bulk and single-cell contact maps. Sci Adv. 2022.