poordub 0.1.2

A minimalistic audio processing library

minidub

A minimalistic PyDub clone.

This small package was written out of curiosity about the audioop module in the Python standard library. It implements a subset of PyDub's features.

You probably should not use it, but it works and illustrates how to use audioop correctly.

PcmAudio objects

The main class in this module is PcmAudio, which is a shrink-wrapped version of PyDub's AudioSegment, but a bit less capable than the original:

• Supports only file formats that Python understands, i.e. Wave, AIFF, and SunAudio.
• Does everyting in-memory
• Has no fancy audio effects (other than fades)

Usage

To read a file from disk, use PcmAudio.from_file(audio_file, audio_format=wave), where audio_file can be a path or a file-like object, and audio_format can be either wave, aifc, or sunau.

Approximately a second of a simple sine wave can be obtained with PcmAudio.sine(hz), and silence with PcmAudio.silence(millis=0).

To add audio parts, use + like so: part1 + part2. To loop, multiply with the number of repetitions: audio * 3

To extract a segment from an audio clip, slice it at the desired time: audio[start:end], where start and end should be in milliseconds, defaulting to 0 and the total audio length, respectively. The total audio length can be obtained with len(audio).

To change the amplitude, add or subtract the desired amplitude change in dB: audio - 3.

To overlay two audio clips, use clip1 & clip2, but careful: This adds the signals, which might result in ugly noise if the sum of amplitudes is greater than the maximum possible amplitude for the sample width. If that happens, add some negative gain to the clips before overlaying them.

Also make certain that audios have the same length before overlaying them. Otherwise, the longer part will be clipped.

A rough measure of the signal strength can be obtained with audio.dbfs(). If it is too low, audio.normalize(headroom=0.1) will scale it to the max with a safety margin, given in dB by headroom.

To write audio files, use audio.to_file(audio_file, audio_format=wave, compression=None). audio_file and audio_format are as above, and compression is only supported for AIFF files.

A memory buffer containing an audio file can be obtained with audio.to_buffer(self, audio_format=wave, compression=None). To play a clip, call audio.play() which returns a simpleaudio.PlayObject.

Fades

The only included effects are fades:

• audio.fade_in(duration, threshold=float('-inf'))
• audio.fade_out(duration, threshold=float('-inf'))
• audio.cross_fade(other, duration, gap=0, threshold=float('-inf'))

For these, duration is in milliseconds as usual, and threshold is the minimum amplitude that needs to be exceeded in the portion being faded before the actual fade is applied.

While this sounds somewhat technical, it improves the audible result of cross-fades: If one part is already very low at the beginning or the end, it needs no additional fade, but can be used as-is in the overlay. Try -9dB for testing.

Finally, the gap is the duration (in milliseconds) of additional silence that is inserted at each end of the audio parts during cross-fades. It can be used to make the transition from one clip to another audibly clearer.

Misc

audio.to_mono() and audio.to_stereo() do what their names suggest. Additionally, there are two technical operations to_framerate() and to_sample_width() which are used internally to ensure consistency between clips before appending or overlaying.

Playback and recording

Playback and recording use PyAudio, which in turn depends on the cross-platform portaudio library. The former can be installed with pip3 install PyAudio, the latter with apt-get, brew or similar. PyAudio is not installed by default as a dependency, it should be done manually before microphones or speakers are used.

The AudioStream wrapper takes care of frame I/O in blocking mode. The open method expects PcmAudio.Params with the desired number of channels, sample width and frame rate. By default, it opens a stream in playback mode. Pass input=True for recording.

AudioStream can be used as a context manager that opens the stream with default settings and closes it on exit.

Example code:

with AudioStream( AudioStream.CD_AUDIO) as out:
    out.play( some_audio)

with AudioStream( AudioStream.MONO_16KHZ).open( input=True) as in_out:
    recording = in_out.record( 3000)
    in_out.play( recording)