pulses 1.0.1

Pulse LEDs on RPi

Pulses

Pulses is a python module to drive LEDs on RPi using PWM (Pulse Width Modulation)

BUILD

1. Clone the repo

   https://gitea.mistrali.pw/musicalbox/pulses.git

2. pip install requirements-dev.txt

3. poetry build

4. pip install dist/pulses-<version>-py3-none-any.whl

GPIO and PWM

For more info on PWM refer to PWM and for information on the different GPIO pin you can read this.

CLI tool

There is a CLI tool, called pulses that you can use to test loops and pulses. Run pulses -h to read the usage instructions.

Work model

Each ledPulse object has some attributes that define the pulse, i.e. the light pattern of the managed LED.

The state of the LED is controlled by the following parameters:

• min: minimum brightness value, I suggest to avoid using 0, start from 2;
• max: maximum brightness;
• delay: the base delay between each step of the pattern;
• initialMethod: the method used to calculate the initial steps of the pattern;
• loopMethod: the method used to calculate the steps of the main loop;
• finalMethod: the method used to calculate the final steps of the loop;
• delayMethod: the method used to calculate the delay between each step;

Each pattern starts running 50 steps of initial values, then goes into a repeteated loop, on exit it runs other 50 steps of final values.

To change the above parameters we use a FIFO queue, each time we set a new value of one of the above attributes, ledPulse will calculate a tuple of 3 values, each element of the tuple is in turn an array of 2-ples, each of these 2-ples has the first element as the value at a specific step, the second element is the delay at a specific step.

• initialValues: 50 elements, if an initialMethod is defined, empy otherwise. These are the values that define the pattern of the LED at the start of the new loop;
• loopValues: 100 elements, never empy. These are the values that define the pattern of the LED at the core infinite loop;
• finalValues: 50 elements, if a finalMethod is defined, empy otherwise. These are the values that define the pattern of the LED at the end of a terminating loop;

An example

Let's say we define a new pattern that has:

• initialMethod = linear;
• loopMethod = cos;
• finalMethod = linear;
• delayMethod = constant;
• delay = 0.01;
• min = 2;
• max = 50;

The LED starts from brightness 0, in 50 steps goes linearly to brightness 50, i.e. the brightness will increate of 1 at each step, there is a delay of 0.01 seconds between each step. After these first 50 steps, there will be a repeating loop, looping on cosine values, so going from brightness 50 (value of max), down to brightness 2 (value of min), the up again to brightness 50, still with a constant delay of 0.01 between each step. The moment we will add a new tuple of values to the queue, using the set() method, the worker will exit from the repeating loop, run on 50 steps of the final values and then start with a new similar loop with the new values.

Class

The only class defined is called ledPulse, it is derived from threading.Thread and takes care of managing the led connected to a PWM GPIO.

Methods

__init__: quite simple, the only parameter is the GPIO pin we want to use. This method takes care of:

• setting up logging;
• setting up PWM;
• installing the default methods for loops and delays;
• set up the queue that we will use later on;

set(): change one or more parameter of the state. Bear in mind that each parameter is standalone, so if min is set to 2 and max is set to 20, calling led.set(max=40) will only change the value of max parameter, leaving all the others at the previous value. After successfully setting a parameter, the values for initial, loop, final and delay are recalculated and a new tuple is added to the queue;

run: this method runs the main loop, that executes first a loop of 50 steps with initialValues if this is not empty, then loops on loopValues until there is a new tuple in the queue OR the stop_event event is set. If there is a new tuple in the queue, the infinite loop on loopValues is interrupted, another loop of 50 steps runs through finalValues (if not empty) and then we go to the main loop, pull the tuple from the queue and start all over, unless stop_event is set; if that's the case we bail out of the external loop and the thread is going to stop;

Plugins

Pulses uses plugin methods to calculate the values and delays for each loop. These plugin methods are nothing more than python functions, following this prototypes:

• for value plugins:

def value_methodname(obj, step):
    return <value for step>

• for delay plugins:

def delay_methodname(obj, step):
    return <delay value for step>

obj is the LED object that uses the method, so you can refer to the attributes of if, like obj.max or obj.min.

Some examples, that are predefined in Pulses:

def delay_constant(obj, step):
    # Delay method: constant
    return obj.delay

def value_sin(obj, step):
    """
    Value method: sin
    Sinusoidal values, 0-1-0 /\
    """

    delta = obj.max - obj.min
    radians = math.radians(1.8 * step)
    return delta * math.sin(radians) + obj.min

def value_on(obj, step):
    """
    Value method: on
    Always on at "max" brightness
    """

    return obj.max

You can write your own method plugins, trying to keep them quite simple possibly, then you have to register them before being able to use them. You can use two specific methods to register plugins based on their kind:

• register_delay_method(methodName, function);
• register_value_method(methodName, function);

For example, we can write a function that returns a random value between min and max:

in mymodule.py:

def value_random(obj, step):
    return random.randint(obj.min, obj.max)

then we can register it

from pulses import ledPulse
from mymodule import value_random

led = ledPulse(12)
led.register_value_method('random', value_random)
led.set(loopMethod='random')

from now on we can call led.set(loopValue='random') and our LED will blink with a random value at each step.