Skip to main content

Control GPIO, I2C and SPI

Project description

This package provide methods for controlling GPIO pins, I2C and SPI buses.
This is written for A20-SOM, but it can be used with other boards. If you do
this we cannot guarantee proper operation of the module. Before using this
package we recommend reading the article at olimex wiki:

https://www.olimex.com/wiki/A20-SOM

When using GPIO make sure that the desired gpio is not used by another periphery.


GPIO METHODS
============

init() - Make initialization of the module. Always must be called first.
getcfg() - Read current configuration of gpio.
setcfg() - Write configuration to gpio.
input() - Return current value of gpio.
output() - Set output value.
pullup() - Set pull-up/pull-down.


The available constants are:

NAME - EQUALS TO
==== =========
HIGH -> 1
LOW -> 0
INPUT -> 0
OUPTUT -> 1
PULLUP -> 1
PULLDOWN -> 2


The gpio are named two ways:

By port name: PH0, PG2, PE10, etc.
These can be imported from port module:

>>> from pyA20SOM.gpio import port
>>> dir(port)

By connector name and pin number: gpio2p12, gpio3p8, etc.
These can be imported from connector module:

>>> from pyA20SOM.gpio import connector
>>> dir(connector)

Generally these constants are just an offset in the memory from the base GPIO address, so they can
be assigned to a number type variable.

>>> led = port.PH2
>>> print led
226



I2C METHODS
===========

init() - Make initialization of the module
open() - Begin communication with slave device
read() - Read from slave device
write() - Write data to slave device
close() - End communication with slave device


SPI METHODS
===========

open() - Open SPI bus with given configuration
read() - Read data from slave device without write
write() - Write data to slave device without read
xfer() - Do write and after that read
close() - Close SPI bus



Examples
========

GPIO::

#!/usr/bin/env python

from pyA20SOM.gpio import gpio
from pyA20SOM.gpio import port
from pyA20SOM.gpio import connector

gpio.init() #Initialize module. Always called first

gpio.setcfg(port.PG9, gpio.OUTPUT) #Configure LED1 as output
gpio.setcfg(port.PG9, 1) #This is the same as above

gpio.setcfg(port.PE11, gpio.INPUT) #Configure PE11 as input
gpio.setcfg(port.PE11, 0) #Same as above

gpio.pullup(port.PE11, 0) #Clear pullups
gpio.pullup(port.PE11, gpio.PULLDOWN) #Enable pull-down
gpio.pullup(port.PE11, gpio.PULLUP) #Enable pull-up

while True:
if gpio.input(port.PE11) == 1:
gpio.output(port.PG9, gpio.LOW)
gpio.output(port.PG9, 0)
else:
gpio.output(port.PG9, gpio.HIGH)
gpio.output(port.PG9, 1)


I2C::

#!/usr/bin/env python

from pyA20SOM import i2c

i2c.init("/dev/i2c-2") #Initialize module to use /dev/i2c-2
i2c.open(0x55) #The slave device address is 0x55

#If we want to write to some register
i2c.write([0xAA, 0x20]) #Write 0x20 to register 0xAA
i2c.write([0xAA, 0x10, 0x11, 0x12]) #Do continuous write with start address 0xAA

#If we want to do write and read
i2c.write([0xAA]) #Set address at 0xAA register
value = i2c.read(1) #Read 1 byte with start address 0xAA

i2c.close() #End communication with slave device


SPI::

#!/usr/bin/env python

from pyA20SOM import spi

spi.open("/dev/spidev2.0")
#Open SPI device with default settings
# mode : 0
# speed : 100000kHz
# delay : 0
# bits-per-word: 8

#Different ways to open device
spi.open("/dev/spidev2.0", mode=1)
spi.open("/dev/spidev2.0", mode=2, delay=0)
spi.open("/dev/spidev2.0", mode=3, delay=0, bits_per_word=8)
spi.open("/dev/spidev2.0", mode=0, delay=0, bits_per_word=8, speed=100000)

spi.write([0x01, 0x02]) #Write 2 bytes to slave device
spi.read(2) #Read 2 bytes from slave device
spi.xfer([0x01, 0x02], 2) #Write 2 byte and then read 2 bytes.

spi.close() #Close SPI bus


It's important that you run your python script as root!


Changelog
=========
* pyA20SOM 0.2.1 (30 JUN 2015)
* Fixed issue with SPI xfer function

* pyA20SOM 0.2.0 (03 SEP 2014)
* Initial release

Project details


Download files

Download the file for your platform. If you're not sure which to choose, learn more about installing packages.

Source Distribution

pyA20SOM-0.2.1.tar.gz (13.8 kB view details)

Uploaded Source

File details

Details for the file pyA20SOM-0.2.1.tar.gz.

File metadata

  • Download URL: pyA20SOM-0.2.1.tar.gz
  • Upload date:
  • Size: 13.8 kB
  • Tags: Source
  • Uploaded using Trusted Publishing? No

File hashes

Hashes for pyA20SOM-0.2.1.tar.gz
Algorithm Hash digest
SHA256 1ac1025596cc112964f7caac9a6a523d5da61623c248ccc178c6cbb4bc1b4549
MD5 a720115ef1d3dffe82f42f2157ca1c56
BLAKE2b-256 46d14c35480fb637b41af62c0536ca8ca18d219d7d8e4ec1ce3b2cb7965d5579

See more details on using hashes here.

Supported by

AWS AWS Cloud computing and Security Sponsor Datadog Datadog Monitoring Fastly Fastly CDN Google Google Download Analytics Microsoft Microsoft PSF Sponsor Pingdom Pingdom Monitoring Sentry Sentry Error logging StatusPage StatusPage Status page