smbus2 0.3.0

smbus2 is a drop-in replacement for smbus-cffi/smbus-python in pure Python

smbus2

A drop-in replacement for smbus-cffi/smbus-python in pure Python

Introduction

smbus2 is (yet another) pure Python implementation of the python-smbus package.

It was designed from the ground up with two goals in mind:

1. It should be a drop-in replacement of smbus. The syntax shall be the same.

2. Use the inherent i2c structs and unions to a greater extent than other pure Python implementations like pysmbus does. By doing so, it will be more feature complete and easier to extend.

Currently supported features are:

• Get i2c capabilities (I2C_FUNCS)

• read_byte

• write_byte

• read_byte_data

• write_byte_data

• read_word_data

• write_word_data

• read_i2c_block_data

• write_i2c_block_data

• write_quick

• process_call

• read_block_data

• write_block_data

• block_process_call

• i2c_rdwr - combined write/read transactions with repeated start

It is developed on Python 2.7 but works without any modifications in Python 3.X too.

SMBus code examples

smbus2 installs next to smbus as the package, so it’s not really a 100% replacement. You must change the module name.

Example 1a: Read a byte

from smbus2 import SMBus

# Open i2c bus 1 and read one byte from address 80, offset 0
bus = SMBus(1)
b = bus.read_byte_data(80, 0)
print(b)
bus.close()

Example 1b: Read a byte using ‘with’

This is the very same example but safer to use since the smbus will be closed automatically when exiting the with block.

from smbus2 import SMBus

with SMBus(1) as bus:
    b = bus.read_byte_data(80, 0)
    print(b)

Example 2: Read a block of data

You can read up to 32 bytes at once.

from smbus2 import SMBus

with SMBus(1) as bus:
    # Read a block of 16 bytes from address 80, offset 0
    block = bus.read_i2c_block_data(80, 0, 16)
    # Returned value is a list of 16 bytes
    print(block)

Example 3: Write a byte

from smbus2 import SMBus

with SMBus(1) as bus:
    # Write a byte to address 80, offset 0
    data = 45
    bus.write_byte_data(80, 0, data)

Example 4: Write a block of data

It is possible to write 32 bytes at the time, but I have found that error-prone. Write less and add a delay in between if you run into trouble.

from smbus2 import SMBus

with SMBus(1) as bus:
    # Write a block of 8 bytes to address 80 from offset 0
    data = [1, 2, 3, 4, 5, 6, 7, 8]
    bus.write_i2c_block_data(80, 0, data)

I2C

Starting with v0.2, the smbus2 library also has support for combined read and write transactions. i2c_rdwr is not really a SMBus feature but comes in handy when the master needs to:

1. read or write bulks of data larger than SMBus’ 32 bytes limit.

2. write some data and then read from the slave with a repeated start and no stop bit between.

Each operation is represented by a i2c_msg message object.

Example 5: Single i2c_rdwr

from smbus2 import SMBus, ic_msg

with SMBus(1) as bus:
    # Read 64 bytes from address 80
    msg = i2c_msg.read(80, 64)
    bus.i2c_rdwr(msg)

    # Write some bytes to address 80
    msg = i2c_msg.write(80, [65, 66, 67, 68])
    bus.i2c_rdwr(msg)

Example 6: Dual i2c_rdwr

To perform dual operations just add more i2c_msg instances to the bus call:

from smbus2 import SMBus, ic_msg

# Single transaction writing two bytes then read two at address 80
write = i2c_msg.write(80, [40, 50])
read = i2c_msg.read(80, 2)
with SMBus(1) as bus:
    bus.i2c_rdwr(write, read)

Example 7: Access i2c_msg data

All data is contained in the i2c_msg instances. Here are some data access alternatives.

# 1: Convert message content to list
msg = i2c_msg.write(60, [1, 2, 3, 4, 5, 6, 7, 8, 9, 10])
data = list(msg)  # data = [1, 2, 3, ...]
print(len(data))  # => 10

# 2: i2c_msg is iterable
for value in msg:
    print(value)

# 3: Through i2c_msg properties
for k in range(msg.len):
    print(msg.buf[k])

Installation instructions

smbus2 is pure Python code and requires no compilation. Installation is easy:

python setup.py install

Or just use pip

pip install smbus2