latex-papersize 0.0.0

Change LaTeX paper size and margins to simulate any magnification

Calculate LaTeX paper and margin settings for arbitrary magnification (C) Silas S. Brown, 2005-2009, 2016, 2019-20. Version 1.64.

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

When producing enlarged material in LaTeX for people with low vision, it's often not enough to simply add such things as "\Large" because that doesn't enlarge everything and it can be difficult to achieve the exact desired size, especially if unusual packages are being used as well.

It's more effective to change the LaTeX paper size and margin settings to simulate SMALL PAPER, and then magnify the result up to the desired physical paper size. This magnifies everything, and also adds some clarity for low-vision users because fonts like CMR have different versions at different sizes and the small-sized versions are often meant to be clearer.

This is a Python script to calculate the necessary settings for arbitrary font and page sizes. Works in both Python 2 and Python 3.

BASIC USAGE

In the following instructions, base-size is the point size that the TeX file is based on (if the documentclass specifies 12pt then \small=11 normal=12 \large=14 \Large=17 \LARGE=20 \huge=25), and desired-size is the point size that you want to produce.

The command-line parameters depend on whether you are using latex/dvips or pdflatex.

FOR USE WITH LATEX AND DVIPS:

To print the geometry settings:

python -m latex_papersize base-size desired-size tex

e.g.: python -m latex_papersize 12 26 tex

(If you install latex-papersize.py as /usr/local/bin/latex-papersize, then you can say "latex-papersize" instead of "python -m latex_papersize" throughout these examples.)

The output of this command should then be placed after \documentclass in your .tex file.

Then run latex to make a DVI file, and then do:

python -m latex_papersize base-size desired-size dvi-file

e.g.: python -m latex_papersize 12 26 myfile.dvi

which will print the appropriate dvips command.

FOR USE WITH PDFLATEX:

With pdflatex you need only one command:

python -m latex_papersize base-size desired-size pdftex

the output of this command should go just before egin{document}. NB if using hyperref package, put hyperref AFTER these settings (and if also using pinyin package then put pinyin package after that again)

PAGE NUMBERS:

When invoking latex-papersize.py with the "tex" or "pdftex" options, you can optionally add a fourth parameter to specify how many points to leave for page numbers at the bottom of each page. Normally 15 is a good idea. Leaving this out causes no room to be left for page numbers and \pagestyle{empty} to be added. This does not affect the dvips command.

PAPER SIZES AND MARGINS:

It is assumed that the final physical printout will be on A4 portrait with 10mm margins. You can override this by setting the paper_width and paper_height environment variables (in millimetres) before running, e.g.: paper_width=297 paper_height=210 python -m latex_papersize ... You can also set the environment variables margin_left and margin_top (the right and bottom margins are assumed to be mirrors of these).

If using with non-PDF latex, remember to set the environment variables again when asking latex-papersize.py for the dvips command. Or "export" them so they remain set.

POSTER PRINTING:

If you want to print on a physical paper size that is larger than your printer can handle, you can make up the larger size by sticking together smaller pieces of paper. Perhaps the best way to do this is to use a separate utility that knows about printable areas, cut margins, etc, such as Jos van Eijndhoven's "poster" utility (last known URL: ftp://ftp.es.ele.tue.nl/pub/users/jos/poster/poster.tar.gz )

In this case you can give latex-papersize.py a margin_left and margin_top of 0 (because "poster" will handle the margins), set the paper size and desired point size appropriate for the final poster, use latex/dvips, and run the resulting .ps through "poster" with "-s 1". This is better than getting "poster" to scale, because if any of your fonts are rendered into bitmaps by Metafont (as some CJK fonts are) then you will likely get a better resolution if the final size is given to latex-papersize.py rather than to "poster".

If you're aiming for a specific number of sheets of paper, don't pick a physical size that's an exact multiple of your printer's paper size, because "poster" accounts for unprintable areas and overlaps slightly. Multiply the printer paper's height and width by 0.88 (or 0.86 if you want a visual margin added to the finished poster besides the cutting margins) and try a multiple of that size.

EXAMPLE USAGE IN A SCRIPT:

To typeset a LaTeX file "file.tex" and magnify from 12-point to 26-point, type a line such as the following (after adjusting the documentclass it specifies, and removing or commenting out the documentclass in file.tex):

latex "\documentclass[12pt]{article}$(python -m latex_papersize 12 26 tex)\input{file.tex}" && mv article.dvi file.dvi

Or in pdflatex (slightly more complex because we need to put the settings just before egin{document}): cat file.tex | awk -- "/^ *\begin {document}[^#-~]$/ { print "$(python -m latex_papersize 12 26 pdftex | sed -e 's//\/g')" } { print }" > /tmp/tmp.tex pdflatex "\documentclass[12pt]{article}\input{/tmp/tmp.tex}" && mv article.pdf file.pdf

To run dvips on the .dvi file (not needed for pdflatex):

$(python -m latex_papersize 12 26 file.dvi)