plaster-yaml 2.0.0

A plaster plugin to configure pyramid app with Yaml

plaster-yaml

Configure your applications with YAML (and JSON) structured data.

Introduction

The plaster-yaml plugin lets applications, notably Pyramid applications but also other applications that use the plaster loader interface, accept YAML configuration sources.

By default, Pyramid (etc.) uses the PasteDeploy (.ini) file format for its configuration. With the plaster-yaml plugin, Pyramid applications can also be configured with a YAML configuration file.

For example, one application can be run either of these ways:

pserve development.yaml
pserve development.ini

Because JSON is a subset of YAML plaster-yaml also supports JSON configuration files. The "With pyproject.toml and a setuptools build back-end" section below contains a JSON example.

Installation

With poetry

poetry add plaster-yaml

With pip

pip install plaster-yaml

Usage

The plaster-yaml plugin must be "registered". This is done by configuring a Python package "entry point" using the packaging tool of your choice. How this is done depends on the packaging tool. Examples are given below.

It is the entry point's name, as will be clear in the examples, that "connects" the filename extension of a configuration file to the loader able to parse it. While it is not necessary to know the details, here are the basic concepts: The entry point's name is a config_uri. The scheme is that part of the URI to the left of the colon, and is itself divisible. One of the scheme's components is matched with the filename extension to select the correct loader.

When developing, using an editable install that executes your unpackaged code, after changing your package's configuration your packaging tool must be run in order to finalize the registration. Examples are given below.

No special steps must be taken after configuring a entry point and (correctly) packaging your project. The plaster-yaml plugin is registered when your project's package is installed.

NOTE:
All of the examples given below show not only how the one entry point required to use plaster-yaml is configured, but also show how to configure the entry point that makes your application into a WSGI, web-based, application. The WSGI entry point is always required for Pyramid web applications.

With poetry

Plugin registration is configured in your pyproject.toml, as follows:

[tool.poetry.plugins."paste.app_factory"]
main = "<PATH_TO_MODULE_CONTAINING_MAIN>:main"

When developing, run poetry install to register your plugin after adding the above to your pyproject.toml.

With setuptools

When developing, run pip install -e . to register your plugin after using either of approaches below.

With pyproject.toml and a setuptools build back-end

This is the preferred method.

Plugin registration may be configured in your pyproject.toml, as follows:

[project.entry-points.'paste.app_factory']
main = '<my_app>:main']

Adding a final line to the example lets the application support JSON in additional to YAML and .ini config files:

[project.entry-points.'paste.app_factory']
main = '<my_app>:main']

[project.entry-points.'plaster.loader_factory']
'file+json' = 'plaster_yaml:Loader'

With setup.py

This method is generally obsolete, but it can be used when the [project.entry-points] table is declared "dynamic". However, this method must be used when the deprecated python setup.py ... command is the package building method.

Plugin registration may be configured in your setup.py, as follows:

setup(
    ...,
    entry_points={
     'paste.app_factory': ['main = <my_app>:main'],
     ...
    },
)

Troubleshooting

The following exception means that you did not successfully register the plaster-yaml plugin:

plaster.exceptions.LoaderNotFound: Could not find a matching loader for the scheme "file+yaml", protocol "wsgi".

Read the relevant "Usage" sub-section, above, to find out how to register it properly.

Appendix: A sample YAML config file for Pyramid

The sample YAML config file shown here configures the MYAPP Pyramid application. The YAML mapping of the app key is presented to the Pyramid application as a Python dictionary. (Excepting the "use" key, which is where the system is told that the "MYAPP" python package is the one to use.)

Within your view callable code, the code which processes a web request and produces a response for rendering, the "my_config_data" configuration value is available via request.registry.settings["my_config_data"]. That is, if the usual coding idiom is used and your view is defined with def myview(request):.

Likewise, the settings dict is available to your configuration code as settings. Again, assuming the usual coding idiom of def main(global_config, **settings): is used in your __init__.py. The global_config variable is then a dict containing the content of the config file's top-level DEFAULT key, if any.

For more information see: the Pyramid Startup documentation

###
# app configuration
# http://docs.pylonsproject.org/projects/pyramid/en/latest/narr/environment.html
###

app:
  "use": "egg:MYAPP"

  "pyramid.reload_templates": false
  "pyramid.debug_authorization": false
  "pyramid.debug_notfound": false
  "pyramid.debug_routematch": false
  "pyramid.default_locale_name": en
  "pyramid.includes": []

  "my_config_data": "Fe Fi Fo Fum"

DEFAULT:
  some_data_which_assists_app_startup: {automatic: false}

server:
  use: egg:waitress#main
  host: 0.0.0.0
  port: 6543

logging:
  version: 1
  disable_existing_loggers: false
  formatters:
    console:
      format: '%(asctime)s [%(levelname)s]: %(name)s - %(message)s'
  handlers:
    console:
      class: logging.StreamHandler
      level: INFO
      stream: ext://sys.stdout
      formatter: console
  root:
    level: INFO
    handlers:
      - console
  loggers:
    dummy:
      level: DEBUG