anymodbus

Async-native Modbus RTU client for Python, built on AnyIO and anyserial.

Overview

anymodbus is a small, opinionated Modbus client (RTU and ASCII serial framing) built on AnyIO and anyserial. It is intentionally protocol-only and narrow in scope. It does not ship servers, TCP transport (planned for v0.3), or device-specific drivers — pymodbus is the right choice if you need any of those, and the two libraries can coexist in one project.

The cases anymodbus is built for:

• AnyIO-native. Same code runs under asyncio, uvloop, or trio. pymodbus is asyncio-only.
• Tx-side 3.5-char inter-frame gap. Enforced before sending. pymodbus relies on its concurrency lock plus OS scheduling and does not enforce a pre-tx idle gap.
• Idempotent-only retries by default. Reads (FC 1-4) retry on transient transport errors; writes (FC 5/6/15/16) do not, unless you opt in. Protects against silent double-writes when a successful write's response is lost in transit.
• Strict typing. mypy strict = true plus pyright typeCheckingMode = "strict". pymodbus uses partial-strict mypy and standard pyright.
• Required baudrate and parity. No defaults — mismatched parity silently drops every frame, so making it explicit at the call site is worth the small ergonomic cost.
• Transport-agnostic. Takes any anyio.abc.ByteStream, defaults to an anyserial.SerialPort. TCP support is planned in v0.3 with the same Bus API.

See docs/migration-from-pymodbus.md for an honest comparison.

Requirements

• Python 3.13 or 3.14
• anyio >= 4.13
• anyserial >= 0.1.1

Installation

uv add anymodbus
# or
pip install anymodbus

Optional extras:

uv add "anymodbus[trio]"    # trio runtime

Usage

Async, one slave

import anyio
from anymodbus import open_modbus_rtu


async def main() -> None:
    async with await open_modbus_rtu("/dev/ttyUSB0", baudrate=19_200, parity="even") as bus:
        slave = bus.slave(address=1)
        regs = await slave.read_holding_registers(0x0040, count=2)
        print(regs)


anyio.run(main)

Sync

from anymodbus.sync import open_modbus_rtu

with open_modbus_rtu("/dev/ttyUSB0", baudrate=19_200, parity="even") as bus:
    slave = bus.slave(1)
    regs = slave.read_holding_registers(0, count=4, timeout=1.0)

Reading a 32-bit float across two registers

Word order varies by device — the Modbus spec doesn't standardize multi-register layout. The default is HIGH_LOW × big-endian-within-word, equivalent to struct.pack(">f", ...); pass word_order="low_high" for devices that store the LSW first.

from anymodbus import WordOrder

async with await open_modbus_rtu("/dev/ttyUSB0", baudrate=19_200, parity="even") as bus:
    slave = bus.slave(address=1)
    high_low_value = await slave.read_float(0x0040)  # default
    low_high_value = await slave.read_float(0x0044, word_order=WordOrder.LOW_HIGH)

Wrapping an existing serial port (with RS-485)

from anyserial import open_serial_port, SerialConfig, RS485Config, Parity
from anymodbus import Bus

port = await open_serial_port(
    "/dev/ttyUSB0",
    SerialConfig(
        baudrate=19_200,
        parity=Parity.EVEN,
        rs485=RS485Config(enabled=True, rts_on_send=True, rts_after_send=False),
    ),
)
async with Bus(port) as bus:
    regs = await bus.slave(1).read_holding_registers(0, count=4)

Modbus ASCII framing and a diagnostic loopback probe

from anymodbus import Framing, RegisterSource, open_modbus_ascii

# Classic 7E1 ASCII wire (data_bits=7); 8 also works.
async with await open_modbus_ascii(
    "/dev/ttyUSB0", baudrate=19_200, parity="even", data_bits=7
) as bus:
    slave = bus.slave(30)
    # Cheap, side-effect-free liveness probe (FC08 sub-0 loopback):
    assert await slave.diagnostic_loopback(b"\xab\xcd") == b"\xab\xcd"
    # Read a measurement published as input registers (FC04):
    o2 = await slave.read_float(0, source=RegisterSource.INPUT)

# Caller-owned stream (e.g. a port shared across modes): pick framing explicitly.
from anymodbus import Bus

bus = Bus(my_byte_stream, framing=Framing.ASCII)

Concurrent fan-out across multiple buses

import anyio
from anymodbus import open_modbus_rtu


async def poll_one(path: str, results: dict[str, tuple[int, ...]]) -> None:
    async with await open_modbus_rtu(path, baudrate=19_200, parity="even") as bus:
        results[path] = await bus.slave(1).read_holding_registers(0, count=4)


async def main() -> None:
    paths = ["/dev/ttyUSB0", "/dev/ttyUSB1", "/dev/ttyUSB2"]
    results: dict[str, tuple[int, ...]] = {}
    async with anyio.create_task_group() as tg:
        for p in paths:
            tg.start_soon(poll_one, p, results)
    for path, regs in results.items():
        print(path, regs)


anyio.run(main)

Testing without hardware

from anymodbus.testing import client_slave_pair

async with client_slave_pair(slave_address=1) as (bus, mock):
    mock.holding_registers[0:4] = [10, 20, 30, 40]
    regs = await bus.slave(1).read_holding_registers(0, count=4)
    assert regs == (10, 20, 30, 40)

Documentation

Full documentation will live at https://anymodbus.graysonbellamy.dev/. Starting points:

• Quickstart
• Configuration
• RTU framing
• Decoders & word order
• Exceptions
• Troubleshooting
• Migration from pymodbus

Contributing

Issues and PRs are welcome. To get a local checkout running:

git clone https://github.com/GraysonBellamy/anymodbus
cd anymodbus
uv sync --all-extras
uv run pre-commit install

Before opening a PR:

uv run pytest
uv run ruff check
uv run ruff format --check
uv run mypy
uv run pyright

Hardware-dependent tests are opt-in via pytest -m hardware with ANYMODBUS_TEST_PORT and ANYMODBUS_TEST_SLAVE_ADDRESS set.

License

MIT. See LICENSE.