BENCHLAB Python Core (benchlab-pycore)

BENCHLAB PyCore provides low-level telemetry, sensor I/O, device communication, and configuration utilities for BENCHLAB hardware devices. It includes standardised interfaces for reading sensors, handling serial communication, translating raw sensor data into human-readable formats, and reading and writing all device configuration including fan profiles, RGB profiles, and calibration.

Features

• Device Discovery: Automatically detect connected BENCHLAB devices
• Multi-Variant Support: Compatible with both ORIGINAL (0x10) and BL2 (0x11) device variants
• Sensor Data Reading: Read raw sensor data including power, voltage, temperature, and fan information
• Extended Telemetry (BL2): BL2 variant provides 23 power sensors and 8 temperature sensors (vs 11 and 4 in ORIGINAL)
• Device Configuration: Read and write fan profiles, RGB profiles, friendly name, and calibration
• Calibration Management: Load and store calibration to factory and user flash slots
• Serial Communication: Handle USB-to-serial communication with BENCHLAB devices
• Error Handling: Comprehensive error handling and logging for robust integration

Installation

pip install benchlab-pycore

Quick Start

Basic Device Discovery and Sensor Reading

import serial
from benchlab_pycore.core import get_fleet_info, read_device, read_sensors, translate_sensor_struct

# Discover all connected BENCHLAB devices
devices = get_fleet_info()
print(f"Found {len(devices)} device(s):")
for device in devices:
    print(f"  Port: {device['port']}, UID: {device['uid']}, Firmware: {device['firmware']}")

if devices:
    ser = serial.Serial(devices[0]['port'], 115200, timeout=1)

    # Read device info to determine variant
    info = read_device(ser)
    product_id = info['ProductId']

    # Read and translate sensors
    sensors = read_sensors(ser, product_id=product_id)
    if sensors:
        data = translate_sensor_struct(sensors, product_id=product_id)
        print(f"CPU Power:        {data['CPU_Power']}W")
        print(f"Chip Temperature: {data['Chip_Temp']}°C")
        print(f"ATX12V Voltage:   {data['ATX12V_Voltage']}V")

    ser.close()

Working with BL2 Devices

import serial
from benchlab_pycore.core import (
    get_fleet_info,
    read_sensors,
    read_device,
    translate_sensor_struct,
    BENCHLAB_BL2_PRODUCT_ID,
    BENCHLAB_ORIGINAL_PRODUCT_ID,
)

def read_with_variant_detection(port):
    ser = serial.Serial(port, 115200, timeout=1)
    try:
        device_info = read_device(ser)
        if not device_info:
            return None

        product_id = device_info['ProductId']
        variant = "BL2" if product_id == BENCHLAB_BL2_PRODUCT_ID else "ORIGINAL"
        print(f"Device on {port}: {variant} (Product ID: 0x{product_id:02X})")

        sensors = read_sensors(ser, product_id=product_id)
        if sensors:
            data = translate_sensor_struct(sensors, product_id=product_id)
            print(f"  CPU Power:  {data['CPU_Power']}W")
            print(f"  GPU Power:  {data['GPU_Power']}W")
            print(f"  Chip Temp:  {data['Chip_Temp']}°C")

            if variant == "BL2":
                print(f"  TS_HPWR1_IN:  {data.get('TS_HPWR1_IN', 'N/A')}°C")
                print(f"  TS_HPWR2_OUT: {data.get('TS_HPWR2_OUT', 'N/A')}°C")
            return data
    finally:
        ser.close()

devices = get_fleet_info()
for device in devices:
    read_with_variant_detection(device['port'])

Reading and Writing Configuration

import serial
from benchlab_pycore.core import (
    read_name, write_name,
    read_fan_profile, write_fan_profile,
    read_rgb_profile, write_rgb_profile,
    FanConfigStruct, FanMode, RGBConfigStruct,
    CAL_USER, CAL_FACTORY,
)

ser = serial.Serial("COM4", 115200, timeout=1)

# Read device name
print(f"Device name: {read_name(ser)}")

# Read a fan profile
cfg = read_fan_profile(ser, fan_profile=0, fan_id=0)
if cfg:
    print(f"Fan 0/0: FanMode={cfg.FanMode} FixedDuty={cfg.FixedDuty}%")

# Write a fan profile
cfg = FanConfigStruct()
cfg.FanMode    = FanMode.FIXED
cfg.FixedDuty  = 60
cfg.TempSource = 0
cfg.MinDuty    = 20
cfg.MaxDuty    = 100
cfg.RampStep   = 5
cfg.FanStop    = 0
write_fan_profile(ser, fan_profile=0, fan_id=0, config=cfg)

# Read and write RGB
rgb = read_rgb_profile(ser, rgb_profile=0)
rgb.Mode = 9   # SINGLE_COLOR
rgb.Red  = 255
rgb.Green = 0
rgb.Blue  = 0
write_rgb_profile(ser, rgb_profile=0, config=rgb)

ser.close()

API Reference

Device Discovery

• get_benchlab_ports() → List[Dict[str, str]] Returns all BENCHLAB COM ports without opening them. Each dict has a 'port' key.

• find_benchlab_devices() → List[Dict[str, str]] Scans and returns all connected devices with 'port', 'uid', and 'fw' keys.

• get_fleet_info() → List[Dict[str, Union[str, int]]] Returns all devices with 'port', 'firmware', and 'uid' keys.

Serial Communication

• read_device(ser) → Optional[Dict[str, int]] Reads vendor info. Returns dict with 'VendorId', 'ProductId', 'FwVersion'. Use ProductId to determine variant: 0x10 = ORIGINAL, 0x11 = BL2.

• read_sensors(ser, product_id=None) → Optional[Union[SensorStructOriginal, SensorStructBL2]] Reads all sensors. Pass product_id to select the correct struct.

• read_uid(ser, retries=3, delay=0.2) → Optional[str] Returns device UID as an uppercase hex string.

Data Translation

• translate_sensor_struct(sensor_struct, product_id=None) → Dict[str, Any] Converts raw sensor data to human-readable format. Auto-detects variant from struct type or product_id.

Configuration — Friendly Name

• ping(ser) → bool Sends the welcome command and verifies the device responds correctly.

• read_name(ser) → Optional[str] Reads the device friendly name (up to 30 UTF-8 bytes).

• write_name(ser, name) → bool Writes a new friendly name. Raises ValueError if name encodes to more than 30 UTF-8 bytes.

Configuration — Fan Profiles

Fan profiles are indexed by profile slot (0–2) and fan channel (0–8).

• read_fan_profile(ser, fan_profile, fan_id) → Optional[FanConfigStruct] Reads one fan channel's configuration. Returns FanConfigStruct or None.

• write_fan_profile(ser, fan_profile, fan_id, config) → bool Writes a fan channel configuration.

FanConfigStruct fields (14 bytes, packed):

Configuration — RGB Profiles

RGB profiles are indexed 0–1.

• read_rgb_profile(ser, rgb_profile) → Optional[RGBConfigStruct] Reads one RGB profile. Returns None if the slot is not available.

• write_rgb_profile(ser, rgb_profile, config) → bool Writes an RGB profile.

RGBConfigStruct fields (6 bytes, packed):

Configuration — Calibration

Calibration structs are device-scoped — ORIGINAL and BL2 have different sizes and are automatically selected based on product_id.

CalibrationStruct / CalibrationStructBL2 fields:

Each CalibrationValueStruct entry has:

• Offset (int16): Additive offset in raw ADC units

• GainOffset (int16): Gain offset (Q12 fixed-point, multiplier = 4096)

• read_calibration(ser, product_id=None) → Optional[Union[CalibrationStruct, CalibrationStructBL2]] Reads the full calibration table from RAM. Selects the correct struct automatically.

• write_calibration(ser, calibration, product_id=None) → bool Writes the full calibration table to RAM in chunks (max 62 bytes per packet).

• write_calibration_chunk(ser, offset, chunk, product_id=None) → bool Writes a raw byte slice at a given offset. Used internally by write_calibration().

• load_calibration(ser, cal_id, product_id=None, fw_version=None) → bool Loads a calibration slot from flash into RAM. Slot numbers are firmware-dependent — prefer CalSlot with the device identity (see store_calibration below).

• store_calibration(ser, cal_id, product_id=None, fw_version=None) → bool Saves the current RAM calibration to a flash slot. The slot numbers differ by firmware version (they swapped in ORIGINAL fw03 / BL2 fw04), so pass a CalSlot with the device identity and let it resolve: store_calibration(ser, CalSlot.USER, info["ProductId"], info["FwVersion"]). Writing the wrong number overwrites the factory slot.

Configuration — Actions

• send_action(ser, action, param1=0, param2=0, param3=0) → bool Sends a one-shot action. Action codes from config.h: CONFIG_ACTION_SAVE=0, CONFIG_ACTION_LOAD=1, CONFIG_ACTION_RESET=2.

Sensor Data Format

translate_sensor_struct() returns a flat dictionary. Sensors marked [BL2] are only available on BL2 devices.

Power Totals

• SYS_Power: Total system power (W)
• CPU_Power: CPU power — EPS1 + EPS2 (W)
• GPU_Power: GPU power — PCIE1 + PCIE2 + PCIE3 + HPWR1 + HPWR2 (W)
• MB_Power: Motherboard power — ATX3V + ATX5V + ATX5VSB + ATX12V (W)

Per-Rail Voltage / Current / Power

Each rail exposes {Rail}_Voltage (V), {Rail}_Current (A), {Rail}_Power (W).

Temperature & Humidity

• Chip_Temp: MCU chip temperature (°C)
• Ambient_Temp: Ambient temperature (°C)
• Humidity: Relative humidity (%)
• TS_1–TS_4: External temperature sensors (°C) — None if no sensor connected
• TS_HPWR1_IN, TS_HPWR1_OUT, TS_HPWR2_IN, TS_HPWR2_OUT — [BL2]

Fans (All Devices)

• Fan1_Duty–Fan9_Duty: Duty cycle (%)
• Fan1_RPM–Fan9_RPM: Speed (RPM)
• Fan1_Status–Fan9_Status: Enable status (0=off, 1=on)
• FanExtDuty: External fan duty cycle (%)

Voltage Inputs (All Devices)

• VIN_0–VIN_12: Additional voltage inputs (V)
• Vdd: Supply voltage (V)
• Vref: Reference voltage (V)

Total sensor count: ~75 keys for ORIGINAL, ~127 keys for BL2.

Integration Examples

MQTT Telemetry Pipeline

import serial
import paho.mqtt.client as mqtt
from benchlab_pycore.core import get_fleet_info, read_device, read_sensors, translate_sensor_struct

def publish_sensor_data(client, device_port):
    ser = serial.Serial(device_port, 115200, timeout=1)
    try:
        info = read_device(ser)
        pid = info['ProductId'] if info else None
        sensors = read_sensors(ser, product_id=pid)
        if sensors:
            data = translate_sensor_struct(sensors, product_id=pid)
            for key, value in data.items():
                topic = f"benchlab/{device_port}/{key}"
                client.publish(topic, value)
    finally:
        ser.close()

client = mqtt.Client()
client.connect("mqtt.example.com", 1883, 60)
for device in get_fleet_info():
    publish_sensor_data(client, device['port'])

Data Logging to CSV

import csv, serial, time
from benchlab_pycore.core import get_fleet_info, read_device, read_sensors, translate_sensor_struct

def log_device_data(device_port, duration_seconds=60, interval_seconds=1):
    filename = f"{device_port}_sensor_log.csv"
    ser = serial.Serial(device_port, 115200, timeout=1)
    info = read_device(ser)
    pid = info['ProductId'] if info else None

    with open(filename, 'w', newline='') as csvfile:
        writer = None
        start = time.time()
        while time.time() - start < duration_seconds:
            sensors = read_sensors(ser, product_id=pid)
            if sensors:
                data = translate_sensor_struct(sensors, product_id=pid)
                data['timestamp'] = time.time()
                if writer is None:
                    writer = csv.DictWriter(csvfile, fieldnames=list(data.keys()))
                    writer.writeheader()
                writer.writerow(data)
                csvfile.flush()
            time.sleep(interval_seconds)
    ser.close()

for device in get_fleet_info():
    log_device_data(device['port'], duration_seconds=300, interval_seconds=5)

Requirements

• Python 3.8+
• pyserial >= 3.5

Development

Installation for Development

git clone https://github.com/BenchLab-io/benchlab-pycore.git
cd benchlab-pycore
pip install -e .

Testing

Unit tests:

pip install pytest
python -m pytest tests/ -v

Hardware tests (safe, read-only by default):

python tests/test_device.py

Automated write validation tests (added in v0.4.1):

python tests/test_write_validation.py                    # safe default tests
python tests/test_write_validation.py --dry-run          # preview without writing
python tests/test_write_validation.py --test-calibration # include calibration tests

See tests/WRITE_TESTING.md for comprehensive write testing documentation.

Interactive configuration tool:

python tests/test_deviceConfig.py          # auto-detects device
python tests/test_deviceConfig.py COM4     # explicit port

Building and Publishing

python -m build
python -m twine upload dist/*

License

MIT License (c) 2025 BenchLab Contributors

Support

For integration questions and support, please refer to the BENCHLAB documentation or contact the development team.