cswap-pin

Keep Claude Code's Remote Control and Artifacts on one account while inference keeps following cswap's account swap.

The problem

cswap swaps the on-disk credential, so everything follows the swap — including two things that are not inference and that you usually want to stay put:

• Remote Control — a session's owner is fixed at creation by whichever bearer created it. Swap accounts and the phone/web loses the session; stale "ghost" sessions pile up on the old account.
• Artifacts — owned by the publishing bearer. After a swap a republish 403s and the artifact "disappears" from the account you are logged into.

Claude Code resolves all of these through one credential accessor and has no per-operation token selector, so splitting auth per operation inside one session means intercepting the requests.

How it works

A local MITM forward proxy that swaps the Authorization bearer on exactly the routes whose server-side ownership is decided by it, and passes everything else — /v1/messages above all — through untouched.

claude session
  HTTPS_PROXY ─► cswap pin proxy ──► (whatever HTTPS_PROXY was already set) ──► api.anthropic.com
                   swaps bearer on: /v1/code/sessions*, /v1/sessions/*,
                                    /api/frame/*, /v1/ultrareview/*
                   passes through:  /v1/messages, /api/oauth/usage, everything else
                   NEVER swapped:   .../worker/*, .../client/presence

Inference keeps billing whichever account cswap has swapped onto. Only the claude.ai-side assets are pinned.

Two exceptions inside the pinned prefix are worth naming, because both were learned by breaking them:

• /worker/* carries the session's own channel credential, not an OAuth bearer. Swapping it makes the server reject every worker call and leaves Remote Control in a reconnect loop.
• /client/presence is registration, not ownership: it tells the server which process is attached and should receive events. Swapped, the server registers the pinned account while the process actually listening belongs to the active one — so inbound has nobody to reach. It returns 200 either way, which is what made it hard to find.

A wrong guess cannot cost you a session

Route classification used to be a single point of permanent failure. Claude Code treats 401/403/404 as terminal — its SSE transport sets state="closed" and never reconnects — so one misrouted swap ended that session's Remote Control for the life of the process (measured: 26 such responses severed four sessions that were still running hours later).

Since 0.1.1 the proxy holds the response before any byte reaches the client, and when the swap is what was refused it re-sends the request exactly as it arrived. "Wrong about this route" degrades to "this request went out unpinned", which is the failure mode everything else here is already built to tolerate.

Install

uv tool install 'claude-swap[pin]'      # or: pipx install 'claude-swap[pin]'

The pin is an optional extra of claude-swap, not a standalone tool: it reads cswap's account store and rewrites the config cswap already manages. Installing cswap-pin on its own does nothing useful.

Use

cswap pin 2          # RC / artifacts / ultrareview → account 2
cswap pin            # show the current pin
cswap pin --clear    # remove it

The pinned account is re-read per request, so cswap pin <other> takes effect under a live daemon — no session restart. The one thing a re-pin cannot move is a Remote Control session that is already open: the server fixed its owner when it was created, so reconnecting inside it is what mints a new one under the new pin.

The port

Nothing is hardcoded. The first daemon binds port 0 — the OS picks — and records what it got in <cswap-backup>/pin-proxy/proxy.json. Later starts try to reclaim that number and fall back to another ephemeral port if anything else already holds it, so a port you are using is never taken from you.

Reclaiming matters because a running session's HTTPS_PROXY is fixed when it execs: coming back on a different port would leave that session dialling an address nothing answers, and its requests would then go out unpinned rather than fail loudly.

Asking for a specific port

cswap pin --get_port          # what it is serving right now (for scripts)
cswap pin --set_port 41234    # serve there from the next daemon start
cswap pin --set_port 0        # back to dynamic: the kernel picks

A port you set outranks the reclaim above — it is a standing instruction, where the reclaim is only about keeping live sessions attached. It takes effect on the next daemon start, not immediately: moving the port under a running session would strand it, since its HTTPS_PROXY was fixed at exec.

If the port you asked for is taken, the pin serves on another one rather than refusing to start, and says so in pin-proxy/daemon.log.

CSWAP_PIN_PORT is not a setting. The pin writes it into .claude.json as its own marker and Claude Code applies that block at boot, so inside a pinned session it already holds the running daemon's port. Exporting it changes nothing; use --set_port.

Requirements

• Python 3.10+
• claude-swap — a peer, not a dependency: this package is loaded by it (see src/cswap_pin/_host.py for the exact surface it borrows)
• cryptography (installed automatically) for the MITM CA

Running the tests

uv sync --group dev                 # pytest, pytest-xdist, and the host
S="$(mktemp -d)" && HOME="$S" XDG_DATA_HOME="$S/.local/share" \
  uv run python -m pytest tests -q

Redirect HOME and XDG_DATA_HOME. The suite drives real cert dirs, daemon state and config wiring; a run against your own HOME will rewrite ~/.claude.json, publish a test CA into ~/.claude/ca-trust.d/, and touch the account store. tests/conftest.py redirects all of it per test, but the env vars are the belt to that suspenders — they are what the child processes the suite spawns obey.

pytest-xdist is required, not optional. addopts = "-n 4" in pyproject.toml runs the suite on 4 workers (12.2s → ~5.0s, measured; more workers do not help — the floor is the single longest test). A pytest without xdist refuses the flag rather than ignoring it, so the suite will not start.

For a serial repro of a failure, add -n 0: xdist gives no live output and truncates tracebacks it cannot attribute to a worker.

One pytest test runs many case_* methods (run_cases in conftest.py), so 60 collected tests carry 321 cases. A failure names both: Class::case_name.

Why a separate package

Upstream did not want a MITM proxy shipped inside claude-swap itself and asked for a companion distribution exposed through an optional extra. See realiti4/claude-swap#198.

Trust

The proxy generates its own CA to re-sign api.anthropic.com and names it in NODE_EXTRA_CA_CERTS. Node accepts exactly one file there, so an existing CA (a corporate MITM, another local proxy) is merged, never replaced — otherwise the session silently loses trust in every host the other proxy re-signs.

The proxy does not authenticate its callers, deliberately. It listens on 127.0.0.1 only, so the population it could turn away is other processes running as you — and an earlier version did exactly that, with a secret file in the cert dir. That defended against nobody: any process able to reach the port could also read a 0600 file in your own home. What it did cost was real, because a session's HTTPS_PROXY is fixed when it execs and cannot be updated in place: arming the credential instantly 407'd every session that had started before it existed.

So the honest boundary is the loopback interface plus your user account, not a credential. If you share a machine with logins you do not trust, do not run this — the pinned account's token is reachable by anything that can reach the port.

License

MIT