daybetter-led-strip 0.3.0

Control Daybetter RGB LED strips over BLE

daybetter-led-strip

Python package to control Daybetter RGB LED strips over BLE. Uses bleak.

Installation

daybetter-led-strip is on PyPI

$ pip install daybetter-led-strip

Usage

The DaybetterLedStrip constructor only requires the device MAC address. After that, the actual underlying device and advertisment data can be updated any number of times using .update_device. If the device disconnects for any reason, it will not reconnect.

from bleak import BleakScanner
from daybetter_led_strip import DaybetterLedStrip
from daybetter_led_strip.const import SERVICE_DISCOVERY

device = await BleakScanner.find_device_by_filter(lambda _device, data: SERVICE_DISCOVERY in data.service_uuids)
    
led_strip = DaybetterLedStrip(device.address)
await led_strip.update_device(device, None)

# turn on
await led_strip.set_power(True)

await asyncio.sleep(1)

await led_strip.set_color((255, 0, 0))

await led_strip.set_power(False)
# Must be called when done using
await led_strip.disconnect()

A complete example program is provided in examples/test.py.

This package was created for use in Home Assistant, which may explain some of the API choices.

Protocol

Communication with the LED strip is done over BLE.

The light strip exposes two services: the generic access profile w/ the device name, and a custom "LED control service" (0xe031).

During discovery, the device also advertises itself with a third service (0xc031) for identification.

The LED control service has a read characteristic (0xf031) and a write characteristic (0xa031). As far as I can tell, the read characteristic cannot actually be read directly. Rather, if notifications are enabled on this service, the device will push updates about its state at various times.

Write Data Format

Commands written to the write characteristic have the following format.

1. The byte 0xA0 (referred to in the app source code as "APP_TO_DEVICE")
2. The command ID. (1 byte)
3. The length of the entire message, not including the checksum. (1 byte) = len(payload) + 3
4. The payload for this command
5. The little-endian CRC16 MODBUS checksum of the rest of the message.

Commands

Command	ID	Payload Description
Get status	0x10	0x00 Results in status payload below being sent on notify
Set power	0x11	0x01 (on) or 0x00 (off)
Show effect	0x12	One of the effect bytes listed below
Set brightness	0x13	A byte representing the brightness, from 0 (0x00) to 100 (0x64). Brightness 0 still has the LEDs slightly on
Set color	0x15	3 bytes, in RGB order

Example command (set to red): A0 15 06 FF 00 00 25 C0

Notify/read data format

The payloads received over notify have a similar structure as the write commands:

1. The byte 0xA1 ("DEVICE_TO_APP")
2. Command ID
3. Length of entire message excluding checksum
4. Payload
5. LE Checksum

Received "commands"

When any of the above write commands are written to the characteristic successfully, the device responds with a message with the same command ID and 0x01 for the payload.

For instance, the above color command would result in A1 15 04 01 F1 1C

When the strip is turned on/off from the IR remote, a message with command ID 0x10 and the payload 00 01 01 64 32 32 ff 31 2d f0 00 00 00 00 (off) or 01 01 01 64 32 32 ff 31 2d f0 00 00 00 00. The first byte indicates the on/off status, but I don't know what the rest means. It seems unrelated to the color of the light.

Running the "get status" command also results in this being sent.

Effects

Note: the brightness can be changed during the following effects. Lower brightnesses result in blinking happening faster, likely because there is a smaller range of brightnesses to interpolate between.

RGB: just red/green/blue

All preset colors: red/green/blue/yellow/teal/purple/white

• 0x02..0x08: show preset colors
• 0x09: switch RGB abruptly, no transition
• 0x0A: switch all preset colors
• 0x0B: fade between colors quickly
• 0x0C: fade between colors slowly
• 0x0D..0x13: blink individual preset colors
• 0x14: fade red/green
• 0x15: fade red/blue
• 0x16: fade green/blue
• 0x17: flash all preset colors
• 0x18..0x1E: flash individual preset colors
• 0x1F: strobe RGB
• 0x20: strobe all colors