fastnet2ip

Reads raw B&G Fastnet data from a serial port, decodes it with pyfastnet, and broadcasts it over UDP in your choice of format — NMEA 0183 or NMEA 2000 (over IP) — for Signal K, OpenCPN, chart plotters, and other navigation software on your network.

Runs on Raspberry Pi, macOS, or Linux. Requires Python 3.10+.

Quick start

Install the CLI in its own isolated environment with pipx:

pipx install fastnet2ip

Run it against your Fastnet serial port:

fastnet2ip --serial /dev/ttyUSB0 --output nmea0183 --live-data
fastnet2ip --serial /dev/ttyUSB0 --output nmea2000 --live-data

No instruments to hand? Replay one of the bundled captures from the source repo (tests/data/):

fastnet2ip --file example1_fastnet_data.txt --output nmea0183 --live-data

--live-data prints a live channel table to the console once per second:

The app can also be invoked as a module: python3 -m fastnet2ip ... — equivalent to the fastnet2ip command.

To upgrade later: pipx upgrade fastnet2ip.

# pip into a virtual environment
python3 -m venv ~/fastnet2ip-venv
source ~/fastnet2ip-venv/bin/activate
pip install fastnet2ip

# from source (development)
git clone https://github.com/ghotihook/fastnet2ip
cd fastnet2ip
python3 -m venv .venv
source .venv/bin/activate
pip install -e ".[test]"

The Fastnet toolkit

Three projects stack together — pick the one that matches where you want the data to end up:

                          ┌─ fastnet2ip   → UDP (NMEA 0183 / NMEA 2000 over IP) → Signal K, OpenCPN, plotters
B&G Fastnet bus ─(serial)─→ pyfastnet ─┤
                          └─ fastnet2n2k → SocketCAN (NMEA 2000 PGNs)           → CAN backbone, chartplotter

This app builds on pyfastnet: pyfastnet handles the protocol layer (frame sync, checksums, decoding raw bytes into named channels); fastnet2ip handles everything above that — reading the serial port, a live data store, mapping channels to output sentences/frames, rate limiting, and UDP broadcast. If you need the data on a physical NMEA 2000 CAN backbone rather than over the network, use fastnet2n2k instead.

Running as a systemd service

For an always-on bridge (e.g. a Raspberry Pi), run fastnet2ip under systemd so it starts on boot and restarts on failure.

Install it globally, not per-user. A plain pipx install goes to a user's ~/.local/bin, which a root-run service can't rely on. Use pipx install --global so the command lands in /usr/local/bin.

1. Install globally with pipx

sudo apt install pipx                        # once, if you don't have it
sudo pipx install --global fastnet2ip

This gives you /usr/local/bin/fastnet2ip, the path the unit below uses. (--global needs pipx ≥ 1.5.)

2. Create the unit file

Paste the following into /etc/systemd/system/fastnet2ip.service (e.g. sudo nano /etc/systemd/system/fastnet2ip.service). The same template ships as fastnet2ip.service in the source repository.

[Unit]
Description=fastnet2ip Service
####################################### CHANGE THIS IF PORT CHANGES
After=dev-ttyUSB0.device
BindsTo=dev-ttyUSB0.device

[Service]
Type=simple
User=root
# Uncomment ONE ExecStart line for the output mode you want:
# NMEA 2000 output:
ExecStart=/usr/local/bin/fastnet2ip --output nmea2000 --serial /dev/ttyUSB0 --udp-port 2000 --n2k-format ydwg --n2k-src 201 --n2k-pri 4 --ignore-gps --log-level INFO
# NMEA 0183 output:
#ExecStart=/usr/local/bin/fastnet2ip --output nmea0183 --serial /dev/ttyUSB0 --udp-port 2002 --log-level INFO
Restart=always
RestartSec=10

# === RESOURCE LIMITS ===
OOMScoreAdjust=-700
OOMPolicy=continue
MemoryMax=128M
MemoryHigh=96M
TimeoutStopSec=30

# === LOGGING ===
StandardOutput=journal
StandardError=journal
SyslogIdentifier=fastnet2ip
Environment=PYTHONUNBUFFERED=1

[Install]
WantedBy=multi-user.target

Before enabling, edit it to match your setup:

• After= / BindsTo= — your serial device, in systemd's escaped form (/dev/ttyUSB0 → dev-ttyUSB0.device)
• the active ExecStart= — pick one line (NMEA 0183 or NMEA 2000) and set the correct --serial port

3. Enable and start it

sudo systemctl daemon-reload
sudo systemctl enable fastnet2ip
sudo systemctl start fastnet2ip
sudo journalctl -u fastnet2ip -f      # follow the logs

To upgrade later: sudo pipx upgrade --global fastnet2ip && sudo systemctl restart fastnet2ip.

Command-line options

Shared

NMEA 2000 (--output nmea2000)

Avoiding feedback loops: --ignore-gps and --ignore-heading

Most B&G systems receive GPS (and sometimes heading) from an external source and pass it through onto the Fastnet bus alongside the instrument data. If you also connect that same source directly to your network, re-broadcasting it from this bridge creates a feedback loop — downstream software sees the same data arriving twice, which can cause jumps, conflicts, or incorrect averaging.

Use --ignore-gps and/or --ignore-heading when that source is already on your network. Both flags work with --output nmea0183 and --output nmea2000. If the bridge is the only source of that data on your network, omit them.

--ignore-gps suppresses:

--ignore-heading suppresses:

Hardware

Fastnet uses two-wire differential transmission. RS-485 adapters work well; the CAN Hat option includes 120 Ω termination which is recommended.

Tested hardware

• Raspberry Pi 4/5/Zero 2W
• Mac
• M5Stack Core MP135 — has RS422/485 built in; a bit more fiddly to set up but good for a permanent install
• DTECH USB RS422/RS485 dongle — works out of the box
• Waveshare RS485 CAN HAT — add to /boot/firmware/config.txt:

  dtoverlay=mcp2515-can0,oscillator=12000000,interrupt=25,spimaxfrequency=2000000
  

Wiring

Serial settings: 28,800 baud, 8 data bits, odd parity, 2 stop bits

Raspberry Pi built-in UART (/dev/ttyAMA*): the first open of a Pi's built-in PL011 UART after a boot can leave the hardware at 9600 even though 28,800 was requested — 28,800 is non-standard, so it takes the kernel's BOTHER path, which has a known first-open quirk (bytes arrive but nothing decodes; a second run "fixes" it). fastnet2ip works around it automatically when opening the port. USB RS-485 adapters (e.g. the DTECH dongle) are not affected. Full diagnosis: docs/uart_first_open_baud_fix.md.

RS485 boards with automatic direction control (e.g. the Waveshare RS485 CAN HAT): the transceiver switches itself to transmit whenever the Pi's TX pin is low, so anything that pulls that pin low reaches the Fastnet bus, even though fastnet2ip never transmits. On the HAT the pin is GPIO14, the Pi's primary UART (serial0):

• Turn off the serial console. In sudo raspi-config → Interface Options → Serial Port, answer No to the login shell and Yes to the serial hardware. Otherwise Linux writes its boot messages, and a login prompt, onto the Fastnet bus.
• If the instruments raise an alarm every time the Pi reboots, pin TX high from the firmware with gpio=14=op,dh in /boot/firmware/config.txt.

Why, and how to confirm it on the wire: docs/rs485_tx_boot_glitch.md.

Output reference

NMEA 0183

True vs Magnetic: The Fastnet data stream carries no magnetic variation or deviation. Whether a channel is labelled True or Magnetic reflects the reference configured in the B&G instrument — not a computed conversion. VHW, HDM/HDT, MWD, and VDR each output whichever reference the instrument is set to.

XDR transducers:

NMEA 2000

Autopilot (127237). The pilot's mode is sent as the steering mode, with the compass target as heading-to-steer — the same as fastnet2n2k:

Wind and compass look the same on the wire, since the standard has no wind mode. The target is dropped in standby and Power, even though Fastnet keeps sending the last one. It is a status broadcast only; nothing here listens for commands.

Raw sensor channels (130824). The uncalibrated readings, for logging, in B&G's own proprietary key-value PGN — byte for byte the frames fastnet2n2k sends, so one decoder reads both. After the B&G header (7D 99) comes a 12-bit key and 4-bit length, then the value. The keys are Fastnet channel numbers, as B&G's own are:

Values are signed 16-bit counts exactly as Fastnet carries them, one key per message (a single CAN frame), sent at full rate and at priority 7. The frame byte by byte, the reasoning and a decoder are in fastnet2n2k's docs/bandg_130824_raw_channels.md. (These replace the PGNs 65280–65282 of earlier versions.)

Wire formats (--n2k-format):

• ydwg — Yacht Devices RAW UDP: HH:MM:SS.mmm R XXXXXXXX DD DD DD..., one line per CAN frame
• pcdin — PCDIN sentences for Signal K server UDP input: $PCDIN,PPPPPP,TTTTTTTT,SS,DDDD...*CC, one sentence per message; fast-packet PGNs carry their whole reassembled payload

How it works

Serial port / hex file
        │
        ▼
  pyfastnet FrameBuffer     ← byte sync, checksum, channel decoding
        │
        ▼
  Live data store           ← latest value per channel
        │
        ▼
  Output handler            ← nmea0183 or nmea2000, selected by --output
        │
        ▼
  UDP broadcast

A message is sent on every channel update — a repeated value is still live data worth putting on the wire — rate-capped at 20 Hz per channel so a fast path can't flood UDP. The four raw sensor channels are the exception: they are for logging, and go out at full rate. There is no dedupe and no periodic re-broadcast: the bridge reflects what the instruments provide, and when a source goes quiet its output stops (consumers time it out themselves). This matches the sibling fastnet2n2k bridge's cadence.

To add a new output format, implement OutputHandler in fastnet2ip/handlers/ and add it to _HANDLERS in fastnet2ip/__main__.py.

Bench testing tools

Two helper scripts for capturing and replaying Fastnet data live in the tools/ directory of the source repository (they are not installed by pip/pipx — clone the repo to use them):

# record raw Fastnet data to file
python3 tools/record_fn.py --port /dev/ttyUSB0 --output my_capture.txt

# play a recording back to a serial port
python3 tools/playback_fn.py --port /dev/ttyUSB1 --input my_capture.txt

# play back at 4x wire speed
python3 tools/playback_fn.py --port /dev/ttyUSB1 --input my_capture.txt --speed 4

Playback is paced at the wire speed implied by the baud rate and framing (28800 baud, 8O2 = 12 bits/byte = 2400 bytes/s), so a capture takes about as long to replay as it did to record while the bus was active. Recordings carry no timestamps, so idle gaps on the original bus are not reproduced — a replay is therefore shorter than the original recording session, and is not a faithful reconstruction of real-world message timing. --speed scales the rate; values above 1.0 are capped by the hardware on a real serial port, but do take effect on a virtual port (pty/socat).

Recordings can also be replayed through the main app with fastnet2ip --file my_capture.txt. Note this uses a different, fixed pacing (256-byte chunks every 50 ms ≈ 5120 B/s) and is not wire-speed accurate.

Development

git clone https://github.com/ghotihook/fastnet2ip
cd fastnet2ip
python3 -m venv .venv
source .venv/bin/activate
pip install -e ".[test]"
pytest

Build distributable artifacts:

pip install build
python -m build        # writes sdist + wheel to dist/

Releasing to PyPI

The version lives in one place — __version__ in fastnet2ip/__init__.py — which pyproject.toml reads automatically.

1. Bump the version in fastnet2ip/__init__.py per semver (patch = bug fix, minor = new backward-compatible flag, major = breaking change).
2. Rebuild clean and validate (stale dist/ files would otherwise be uploaded):

   rm -rf dist build *.egg-info
   python -m build
   twine check dist/*
   

3. Tag and upload:

   git commit -am "Release X.Y.Z"
   git tag vX.Y.Z
   git push origin main --tags
   twine upload dist/*          # needs a PyPI account + API token in ~/.pypirc
   

4. Users upgrade with pipx upgrade fastnet2ip (or pip install --upgrade fastnet2ip).

PyPI never lets you re-upload an existing version — even a deleted or "yanked" one. If a release has a bug, bump to the next patch version and re-publish; you can never overwrite a number that's already live.

Acknowledgments

• trlafleur — collected significant background research
• Oppedijk — protocol background
• timmathews — substantial C++ implementation

License

MIT — see LICENSE.