fastnet2n2k

Reads a B&G Fastnet instrument stream (live serial or a captured hex file), decodes it with pyfastnet, maps the channels to NMEA 2000 PGNs and transmits them onto a physical CAN bus via SocketCAN. Built for the M5Stack CoreMP135 but runs on any Linux box with a SocketCAN interface. Requires Python 3.11+.

Quick start

1. Install the CLI in its own isolated environment with pipx:

sudo pipx install --global fastnet2n2k

This puts a fastnet2n2k command on your PATH (in /usr/local/bin, so a root-run systemd service can find it too). python -m fastnet2n2k ... also works once installed. (--global needs pipx ≥ 1.5.)

2. Bring up the CAN bus (once per boot — restart-ms 100 lets the controller auto-recover from a bus-off):

sudo ip link set can0 up type can bitrate 250000 restart-ms 100
ip -details link show can0    # want: state ERROR-ACTIVE, bitrate 250000

3. Run it — replaying a captured hex file is the safest first test:

# replay a captured Fastnet hex file
fastnet2n2k --file capture.txt --channel can0

# live from the Fastnet bus
fastnet2n2k --serial /dev/ttyUSB0 --channel can0

Find your serial adapter with ls /dev/ttyUSB* /dev/ttyACM* /dev/ttyS*. Add --live-data to print the live channel table once per second. Stop with Ctrl-C.

If can0 shows BUS-OFF, fix that before expecting output — a CAN frame needs at least one other node on the wire to acknowledge it (check termination ≈ 60 Ω, common ground, and CAN-H/CAN-L not swapped). See Verify for a no-instruments loopback test.

git clone https://github.com/ghotihook/fastnet2n2k.git
cd fastnet2n2k
python3 -m venv .venv
source .venv/bin/activate
pip install -e .

The Fastnet toolkit

Three projects stack together — pick the one that matches where you want the data to end up:

                          ┌─ fastnet2ip   → UDP (NMEA 0183 / NMEA 2000 over IP) → Signal K, OpenCPN, plotters
B&G Fastnet bus ─(serial)─→ pyfastnet ─┤
                          └─ fastnet2n2k → SocketCAN (NMEA 2000 PGNs)           → CAN backbone, chartplotter

This app builds on pyfastnet and puts decoded data onto a physical NMEA 2000 CAN backbone. If instead you want it on your network (UDP — Signal K, OpenCPN, a plotter over WiFi), use fastnet2ip.

Running as a systemd service

For an always-on bridge, run fastnet2n2k under systemd so it starts on boot and restarts on failure. The unit runs as root (consistent with fastnet2ip) and brings can0 up itself before starting.

Install it globally, not per-user. A plain pipx install goes to a user's ~/.local/bin, which a root-run service can't rely on. Use pipx install --global so the command lands in /usr/local/bin instead.

1. Install globally with pipx

sudo apt install pipx                        # once, if you don't have it
sudo pipx install --global fastnet2n2k

This gives you /usr/local/bin/fastnet2n2k, the path the unit below uses. (--global needs pipx ≥ 1.5; run which fastnet2n2k to confirm the path.)

2. Create the unit file

A template ships as fastnet2n2k.service in the source repo. Copy it to /etc/systemd/system/ and edit the --serial device and channel to match your setup:

[Unit]
Description=fastnet2n2k Service
After=network.target

[Service]
Type=simple
User=root

# Bring can0 up at the NMEA2000 bitrate — only if it isn't already up, so this is
# safe alongside another CAN service (e.g. an n2k2ip gateway) sharing can0.
ExecStartPre=/bin/sh -c 'ip link show can0 | grep -qw UP || ip link set can0 up type can bitrate 250000 restart-ms 100 2>/dev/null; ip link show can0 | grep -qw UP'

ExecStart=/usr/local/bin/fastnet2n2k --serial /dev/ttyAMA5 --channel can0
Restart=always
RestartSec=10

# === RESOURCE LIMITS ===
OOMScoreAdjust=-700
OOMPolicy=continue
MemoryMax=128M
MemoryHigh=96M
TimeoutStopSec=30

# === LOGGING ===
StandardOutput=journal
StandardError=journal
SyslogIdentifier=fastnet2n2k
Environment=PYTHONUNBUFFERED=1

[Install]
WantedBy=multi-user.target

3. Enable and start it

sudo systemctl daemon-reload
sudo systemctl enable --now fastnet2n2k.service
journalctl -u fastnet2n2k.service -f      # follow the logs

To upgrade later: sudo pipx upgrade --global fastnet2n2k && sudo systemctl restart fastnet2n2k.

Command-line options

Suppressing PGNs

If another device on the bus is the authority for some data — a GPS for position and COG/SOG, say — stop this bridge sending its version of it:

python -m fastnet2n2k --serial /dev/ttyUSB0 --ignore-pgn 129025,129026
python -m fastnet2n2k --serial /dev/ttyUSB0 --ignore-pgn 129025 --ignore-pgn 129026

A suppressed PGN is never built and never sent, and is also dropped from the transmit-PGN list this node advertises to the bus, so it doesn't claim to send what it won't. Only PGNs from the table below are accepted; anything else is a startup error rather than a silent no-op, so a typo can't look like it worked.

Suppression is per PGN, and some PGNs carry more than one kind of data: --ignore-pgn 130306 silences apparent wind, true wind and TWD, --ignore-pgn 130312 silences both sea and air temperature, and --ignore-pgn 130824 silences all four raw sensor channels.

The source address is not a flag — it is left to the nmea2000 library, which picks a preferred address and resolves conflicts via ISO address claiming, then persists the result across restarts.

CAN failure handling: the device reconnects automatically. If can0 isn't up at start it waits (logging retries) rather than exiting; if the bus drops or goes bus-off mid-run, sends fail quietly (logged at most every 5 s) and resume once it recovers — the bridge keeps running. Use --log-level DEBUG for connection/retry detail.

What it sends

Each Fastnet channel is mapped to the matching PGN and emitted only when the channel updates, rate-capped at 0.05 s per path (the raw sensor channels are the exception: they go out at full rate). There is no periodic re-broadcast, so when the instruments go quiet the output stops and consumers time the data out themselves.

The Priority column is each PGN's NMEA 2000 standard CAN priority (0 = highest, 7 = lowest) — the values used unless you override them all with --n2k-priority N. 130824 is proprietary and has no standard priority; it is sent at the lowest so its volume never delays navigation data.

Depth is below keel. The B&G/H2000 applies its keel offset internally, so the depth on the Fastnet wire is already below-keel. Fastnet never reports the transducer-to-keel distance, so PGN 128267's offset field is sent as not-available — the honest encoding for "no offset info" (sending 0 would assert a transducer-at-keel distance we don't actually know). The depth value passes through unchanged either way.

Two consequences for consumers:

• The reading appears under Signal K environment.depth.belowTransducer, because PGN 128267's depth field is below-transducer by definition and belowKeel is a derived path. The number is your below-keel depth; only the label differs. To get a belowKeel path, set transducerToKeel = 0 on the Signal K side and enable the derived-data plugin.
• Do not configure a second keel/transducer offset on any downstream plotter or gateway — it would double-count and read shallow.

Autopilot (127237 Heading/Track Control). The H2000 pilot's mode is sent as the PGN's steering mode, with the compass target as heading-to-steer:

Pilot mode	Steering mode	Heading-to-steer
Standby	Main Steering	not available
Compass	Heading Control	compass target
Wind	Heading Control	compass target
Power	Non-Follow-Up Device	not available
NMEA WP	Track Control	compass target

• Wind and compass look the same on the bus — the standard has no wind mode.
• The target is dropped in standby and Power even though Fastnet keeps sending the last one, so a disengaged pilot never advertises a heading it isn't steering to.
• Engaging reads 0° for one update before the real target arrives. It passes through, because a 0° target can't be told apart from north.
• It is a status broadcast only. A plotter may show autopilot controls on seeing it; they do nothing, since nothing here listens for commands. If that is unwanted, or another autopilot on the NMEA 2000 bus already sends 127237, use --ignore-pgn 127237.

Raw sensor channels (130824, B&G key-value data). The uncalibrated readings — for logging, so calibration can be refitted later — have no standard PGN. They go out in B&G's own proprietary key-value PGN, in B&G's layout: the B&G manufacturer header (7D 99: code 381, marine), then a 12-bit key and 4-bit byte length, then the value. B&G's keys are Fastnet channel numbers (canboat's BANDG_KEY_VALUE table: 65 = Water Speed = 0x41, 127 = VMG = 0x7F, …), so each raw channel keeps its own:

Key	Fastnet channel
66 (0x42)	Boatspeed (Raw)
74 (0x4A)	Heading (Raw)
78 (0x4E)	Apparent Wind Speed (Raw)
82 (0x52)	Apparent Wind Angle (Raw)

• Values are signed 16-bit, unscaled — exactly as Fastnet carries them (format 0x0A), length 2. Heading and wind angle are binary angles (65536 = 360°); the speeds are sensor counts. B&G gear has never been seen sending these four keys, so this value format is ours.
• One key per message, which fits a single CAN frame; every update is sent, at whatever rate the instruments produce it (about 70 frames/s for all four, ~4% of the bus).
• Fastnet actually carries two 16-bit values per raw channel; pyfastnet exposes only the first, so only that is sent. The second could follow later as a 4-byte value under the same key without breaking decoders that honour the length.
• Displays ignore keys they don't know. --ignore-pgn 130824 turns them off.

The frame byte by byte, why it uses B&G's format, a decoder and references are in docs/bandg_130824_raw_channels.md.

Data arrives from pyfastnet 3.0 already in SI on Signal K paths, so it maps almost 1:1 onto NMEA 2000 — no unit conversion here (the raw sensor channels are sensor counts, and pass through as counts). Sign comes straight from the decoded value; True vs Magnetic is carried by the path (the B&G instrument's own reference — the Fastnet stream has no variation to convert).

Encoding, CAN-ID construction, fast-packet framing and ISO address claiming (250 kbit/s, 29-bit IDs) are handled by the nmea2000 library (canboat-based) on top of python-can's socketcan backend.

WiFi gateways: if you feed a WiFi NMEA 2000 gateway downstream, configure it for unicast UDP, not broadcast — WiFi broadcast is unacknowledged and silently drops frames even at low rates.

Verify

Watch the raw frames on the board with can-utils (sudo apt install can-utils):

candump -ta can0

You should see 29-bit frames appear as instruments update — heading, wind, depth, speed, etc. — and stop when they go quiet. On a connected chartplotter / analyzer the device appears in the device list after its ISO address claim (PGN 60928).

Loopback test (no instruments needed)

With can0 and can1 wired together (CAN-H↔CAN-H, CAN-L↔CAN-L, one 120 Ω terminator), can1 provides the ACK so can0 can transmit:

sudo ip link set can1 up type can bitrate 250000 restart-ms 100
candump -ta can1                                       # terminal 1
fastnet2n2k --file capture.txt --channel can0          # terminal 2

On the CoreMP135, the two FDCAN interfaces (SIT1051T transceivers) are exposed as can0 (FDCAN1, PE3/PE10) and can1 (FDCAN2, PG0/PE0).

Hardware notes (M5Stack CoreMP135)

The CoreMP135 runs Linux on an STM32MP135 and exposes its two FDCAN interfaces as the SocketCAN netdevs can0 and can1. Bring up the second interface the same way if you need it:

sudo ip link set can1 up type can bitrate 250000 restart-ms 100   # FDCAN2

Raspberry Pi built-in UART (/dev/ttyAMA*)

On a Pi (including a CM4, which the sample service file targets with /dev/ttyAMA5), the first open of a built-in PL011 UART after a boot can leave the hardware at 9600 even though 28800 was requested — Fastnet's rate is non-standard, so it takes the kernel's BOTHER path, which has a known first-open quirk. fastnet2n2k works around it automatically (_force_baudrate in input_source.py); the full diagnosis and the supporting measurements are in docs/uart_first_open_baud_fix.md.

RS485 tap boards with automatic direction control

If the Fastnet side is tapped through an RS485 transceiver with automatic direction control (Waveshare's carrier boards and HATs use one: TX low raises DE, so the driver turns on whenever TX is low), check what the TX pin does during boot, before the UART overlay muxes it.

On BCM2711 the pad reset defaults split at GPIO8 — GPIO0-8 pull up, GPIO9-27 pull down — so a TX pin in the pull-down range sits low from reset until the kernel claims it, holding the driver on and jamming the instrument bus for the length of every boot. The bridge never transmits, so this is invisible from the software side: the damage is done before its process starts, and by the time data is flowing the bus is healthy again with the instrument alarm already latched.

Pin the line high from the firmware, using the TX GPIO of whichever channel you are on:

# /boot/firmware/config.txt
gpio=12=op,dh

Full diagnosis, the channel/overlay mapping for a CM4 in a CM5 carrier, and how to re-confirm it on the wire are in docs/rs485_tx_boot_glitch.md.

Tests

source .venv/bin/activate
pip install -e . pytest
python -m pytest tests/ -q

The suite drives the mapping with the Fastnet captures in tests/data/ and round-trips the resulting NMEA 2000 messages to assert PGNs, units, T/M references, sign passthrough, the autopilot mode sequence, the raw channels' B&G byte layout, the send throttle (and the raw channels' exemption from it), and the full file→decode→send pipeline.

Sender POC (nmea2000_poc.py)

A standalone minimal proof-of-concept (in the source repo) that transmits a single NMEA 2000 PGN (127250 Vessel Heading) onto the bus — useful for smoke-testing a CAN link independently of the Fastnet pipeline.

python nmea2000_poc.py --channel can0 --heading 90 --once   # single frame
python nmea2000_poc.py --channel can0 --heading 90          # ~10 Hz loop

Options: --channel (default can0), --heading degrees, --ref true|magnetic, --rate Hz, --once.

Desk testing without a bus (virtual CAN)

sudo modprobe vcan
sudo ip link add dev vcan0 type vcan
sudo ip link set up vcan0
candump vcan0                                                 # terminal 1
python nmea2000_poc.py --channel vcan0 --heading 90 --once   # terminal 2

License

MIT — see LICENSE.