findafactor 6.7.0

Find any nontrivial factor of a number

FindAFactor

Find any nontrivial factor of a number

Copyright and license

(c) Daniel Strano and the Qrack contributors 2017-2025. All rights reserved.

Installation

From PyPi:

pip3 install FindAFactor

From Source: install pybind11, then

pip3 install .

in the root source directory (with setup.py).

Windows users might find Windows Subsystem Linux (WSL) to be the easier and preferred choice for installation.

Usage

from FindAFactor import find_a_factor, FactoringMethod

to_factor = 1000

factor = find_a_factor(
    to_factor,
    method=FactoringMethod.PRIME_PROVER,
    node_count=1, node_id=0,
    gear_factorization_level=23,
    wheel_factorization_level=13,
    sieving_bound_multiplier=1.0,
    smoothness_bound_multiplier=1.0,
    gaussian_elimination_row_offset=3,
    check_small_factors=False,
    wheel_primes_excluded=[]
)

The find_a_factor() function should return any nontrivial factor of to_factor (that is, any factor besides 1 or to_factor) if it exists. If a nontrivial factor does not exist (i.e., the number to factor is prime), the function will return 1 or the original to_factor.

• method (default value: PRIME_PROVER/0): PRIME_PROVER/0 will prove that a number is prime (by failing to find any factors with wheel and gear factorization). FACTOR_FINDER/1 is optimized for the assumption that the number has at least two nontrivial factors.
• node_count (default value: 1): FindAFactor can perform factorization in a distributed manner, across nodes, without network communication! When node_count is set higher than 1, the search space for factors is segmented equally per node. If the number to factor is semiprime, and brute-force search is used instead of congruence of squares, for example, all nodes except the one that happens to contain the (unknown) prime factor less than the square root of to_factor will ultimately return 1, while one node will find and return this factor. For best performance, every node involved in factorization should have roughly the same CPU throughput capacity. For FACTOR_FINDER mode, this splits the sieving range between nodes, but it does not actually coordinate Gaussian elimination rows between nodes.
• node_id (default value: 0): This is the identifier of this node, when performing distributed factorization with node_count higher than 1. node_id values start at 0 and go as high as (node_count - 1).
• gear_factorization_level (default value: 23): This is the value up to which "wheel (and gear) factorization" are applied to "brute force." A value of 23 includes all prime factors of 23 and below and works well for PRIME_PROVER, though significantly higher might be preferred in certain cases. In FACTOR_FINDER, one probably wants to avoid setting a different gear level than wheel level.
• wheel_factorization_level (default value: 13): "Wheel" vs. "gear" factorization balances two types of factorization wheel ("wheel" vs. "gear" design) that often work best when the "wheel" is only a few prime number levels lower than gear factorization. For PRIME_PROVER, optimized implementation for wheels is only available up to 17; for FACTOR_FINDER, wheels are constructed programmatically while avoiding wheel_primes_excluded entries, so there is no fixed ceiling. The primes above "wheel" level, up to "gear" level, are the primes used specifically for "gear" factorization. For FACTOR_FINDER method, wheel factorization is applied to map the sieving interval onto non-multiples on the wheel, if the level is set above 1.
• sieving_bound_multiplier (default value: 1.0): This controls the sieving bound and is calibrated such that it linearly multiplies the number to factor minus its square root (for a full 1.0 increment, which is maximum). While this might be a huge bound, remember that sieving termination is primarily controlled by when gaussian_elimination_row_multiplier is exactly satisfied.
• smoothness_bound_multiplier (default value: 1.0): This controls smoothness bound and is calibrated such that it linearliy multiplies pow(exp(0.5 * sqrt(log(N) * log(log(N)))), sqrt(2.0)/4) for N being the number to factor (for each 1.0 increment). This was a heuristic suggested by Elara (an OpenAI custom GPT).
• gaussian_elimination_row_offset (default value: 1): This controls the number of rows greater than the count of smooth primes that are sieved before Gaussian elimination. Basically, for each increment starting with 1, the chance of finding at least one solution in Gaussian elimination goes like (1 - 2^(-m)) for a setting value of m: 1 value is a 50% chance of success, and the chance of failure is halved for each unit of 1 added. So long as this setting is appropriately low enough, sieving_bound_multiplier can be set basically arbitrarily high.
• check_small_factors (default value: False): True performs initial-phase trial division up to the smoothness bound, and False skips it.
• wheel_primes_excluded (default value: []): If using FACTOR_FINDER method, these specific primes are excluded from wheel and gear factorization (up to wheel_factorization_level and gear_factorization_level). (See wheel_tuner.py in the project root for guidance on which primes to exclude and include, based empirically upon a sample list of smooth numbers for your particular number to factor.)

All variables defaults can also be controlled by environment variables:

• FINDAFACTOR_METHOD (integer value)
• FINDAFACTOR_NODE_COUNT
• FINDAFACTOR_NODE_ID
• FINDAFACTOR_GEAR_FACTORIZATION_LEVEL
• FINDAFACTOR_WHEEL_FACTORIZATION_LEVEL
• FINDAFACTOR_SIEVING_BOUND_MULTIPLIER
• FINDAFACTOR_SMOOTHNESS_BOUND_MULTIPLIER
• FINDAFACTOR_GAUSSIAN_ELIMINATION_ROW_OFFSET
• FINDAFACTOR_CHECK_SMALL_FACTORS (True if set at all, otherwise False)
• FINDAFACTOR_WHEEL_PRIMES_EXCLUDED (comma-separated prime numbers)

About

This library was originally called "Qimcifa" and demonstrated a (Shor's-like) "quantum-inspired" algorithm for integer factoring. It has since been developed into a general factoring algorithm and tool.

Special thanks to OpenAI GPT "Elara," for help with indicated region of contributed code!