flashgate

flashgate answers one specific question: the firmware you just built — does it actually run on the board?

It automates the whole chain: compile, flash over ST-Link, wait for the board to report its own identity, then drive the actual feature over the console and assert on hardware register readbacks. Any broken step ends with a non-zero exit code and a reason.

build → flash over ST-Link → board boots → evidence → probes → exit code

中文说明 | 使用说明（推荐先读这份）

How the board testifies

Two evidence channels, picked per bench (evidence.mode: uart / swd / auto):

The firmware prints its identity over the console UART, and also publishes a 64-byte signature (magic + git sha + build time + CRC32) at a fixed RAM address that the host reads through the ST-Link alone — no serial cable needed for boot verification:

FLASHGATE-BOOT board=apollo-h743 git=2c58bd3 build=2026-08-28T07:26:35Z rtos=FreeRTOS

Both carry the git sha plus -dirty when the tree differs from HEAD, so a passing verify proves the board is running a build of your current HEAD (-dirty marks uncommitted changes; it does not fingerprint their content — the Stop hook's tree fingerprint covers that side: tracked diffs in full, untracked files and the board profile by path + size + first 4 MiB, plus the flashgate version itself, so tightening probe expectations or upgrading the tool invalidates a cached PASS. Files ignored by git and nested git repositories are outside the gate). Functional probes then send real commands and assert on the answers, including register readbacks (TIM3 CCR), not firmware self-reports:

- send: "led0?"
  expect: "OK led0 state={state} ccr={ccr:d}"   # mirror of the firmware's printf
  assert: "state == BREATH and ccr <= 1000"

Quick start

pip install -e .                 # Python 3.11+
pip install -e ".[mcp]"          # optional MCP server
pip install -e ".[bench]"        # optional remote bench (device-connect)

flashgate doctor                 # ST-Link / serial / toolchain sanity
flashgate verify --all-probes    # build → flash → evidence → sha → probes
echo $?                          # 0 = the board confirms it works

Requires an ST-Link; a USB-TTL adapter on the console UART adds probes. The repo ships a complete buildable example for the ALIENTEK Apollo STM32H743 (examples/apollo-h743/) with the Stop hook pre-wired, so a fresh clone verifies out of the box once wired up.

Exit codes

Contributing

Board profiles, probes, fixes and docs are welcome — see CONTRIBUTING.md for the setup and contribution terms.

The Stop hook

hooks/flashgate_stop.py is a Claude Code Stop hook (any harness implementing the same hook contract works). When the agent tries to finish after touching watched firmware files, the hook fingerprints the tree (plus the board profile — editing verification semantics must not reuse a cached green) and allows instantly if that exact state already passed hardware verify (~0.7 s cached). Otherwise it runs the full verify on the real board and blocks the stop on failure, feeding the agent the board's testimony:

[flashgate] BLOCKED (attempt 1/2): firmware changes are not verified on hardware (verify rc=7).
[flashgate] last verify output:
    step 1: led-demo> led0 breath
    board: OK led0 state=OFF          ← readback exposes the silent no-op

The same broken tree is blocked at most twice, then released with a loud warning — the session can never wedge, and a failure is never silently swallowed.

Verification records

Every verify — passing or failing — leaves an evidence record at <firmware>/.flashgate/records/<ts>-<exit>-<fingerprint8>.json: the per-check verdicts (build/flash/boot/identity/probe:*, with skipped meaning never executed, never a silent absence), the raw evidence behind them (banner line, SWD signature fields, console tails, failing probe transcripts), the artifact sha256, and the exact tree+profile+tool-version identity the verdict applies to. The MCP verify tool returns the same record inline as data.record. Format: docs/record-schema.md. Keep .flashgate/ in your firmware repo's .gitignore (the shipped example does), or every record write churns the fingerprint. A record that cannot be written is a warning, never a changed exit code — and a crashed run still leaves one. The newest ~500 records are kept (best-effort pruning). flashgate verify --json prints this run's record as pure-ASCII JSON on stdout (human logs move to stderr) for scripting — safe on any console codepage.

Remote bench (device-connect, Stage 2)

Expose this bench to any agent on the network over Arm's device-connect protocol — four named RPCs over a BenchDriver core, nothing else (no arbitrary shell, no path arguments; the board a bench serves is fixed by its profile):

pip install "flashgate[bench]"          # optional extra -> device-connect-edge
DEVICE_CONNECT_ALLOW_INSECURE=true DEVICE_CONNECT_DISCOVERY_MODE=d2d   flashgate --board boards/apollo-h743.yaml bench-serve

Remote callers discover device_type=flashgate-bench and use describe_bench / start_verify / get_operation / cancel_operation, plus a verify_completed event per operation at its terminal state (an operation drained during server shutdown does not emit one — polling remains the authoritative contract). start_verify returns an op_id immediately (single verify at a time — a client retrying over a flaky network can never trigger a second flash); poll get_operation to the terminal snapshot, which carries the exit code and the run's full evidence record. Stop the server without hunting PIDs: flashgate --board <profile> bench-serve --stop (it drains the in-flight operation, then exits).

The red line for every consumer: the mesh wraps any normally-delivered reply as success: true — including a busy bench answering {"error": "busy"}. Judge verification ONLY by the operation payload (state / exit_code / the record's checks), never by transport success. Acceptance on the Apollo bench: the same firmware input produces identical local and remote domain results (tree fingerprint and per-check verdicts equal; artifact_sha256 differs by design — it identifies the BUILD, which embeds its timestamp, while the tree fingerprint identifies the SOURCE).

Deployment notes (from the first real cross-host test, wired host

• Wi-Fi laptop, 2026-09-15):

• Multicast discovery does not cross all wired↔wireless routers. If discovery finds nothing across machines but ping works, switch to unicast: on the bench host set ZENOH_LISTEN=tcp/0.0.0.0:7447 before bench-serve; on the client set MESSAGING_URLS=tcp/<host-ip>:7447.
• Open UDP 7446 (multicast scouting) or TCP 7447 (unicast) inbound on the host's firewall; a Wi-Fi client set to "Public network" blocks the announcements it needs to receive.
• One bench-serve per bench: a second instance for the same firmware dir is refused at startup (a loopback lock socket, released automatically when the process dies). Before the lock existed, two same-named servers split-brained the mesh and raced each other for the board's serial port.

Third-party licensing: the bench extra depends on device-connect-edge (Apache-2.0) as a pip dependency only — flashgate stays MIT, and no device-connect source is vendored into this repository (fixes go upstream as PRs). Commercial distributions that bundle the dependency must include its LICENSE and NOTICE files.

Security posture, stated plainly: D2D mode is zero-authentication — anyone on the same LAN can discover the bench and start_verify, which FLASHES THE BOARD. Descriptions and records also carry local paths. Fine for a home bench; for anything shared, put the mesh behind authenticated infrastructure (device-connect server mode) — Stage 4 work.

Install as a Claude Code plugin

The repo doubles as a Claude Code plugin: the Stop hook, an MCP server, a board-integration skill and /flashgate commands, all at once:

pip install git+https://github.com/Lion-1209/flashgate        # CLI + hook runtime
pip install "flashgate[mcp] @ git+https://github.com/Lion-1209/flashgate"  # + MCP

Then inside Claude Code:

/plugin marketplace add Lion-1209/flashgate
/plugin install flashgate@flashgate

The hook needs to know your board profile: set FLASHGATE_BOARD to your board yaml (or a repo boards/ default is used when present). Without a profile the gate stays idle and says so.

MCP server

{ "mcpServers": { "flashgate": {
    "command": "flashgate-mcp",
    "args": ["--board", "/path/to/boards/apollo-h743.yaml"] } } }

board_info, doctor, build, flash, verify, probe, console_send, console_read. Any MCP-capable agent can drive the board directly. Every tool returns a structured result envelope (status, stable code, summary, CLI exit_code, log) — never a bare log to parse. mcp 1.x and 2.x supported.

Demos

Real-hardware recordings, indexed in demo/: doctor, green-path verify, boot-timeout catch, probe catching a silent no-op, Stop-hook escalation — plus the full session of a real Claude Code agent getting blocked, diagnosing the firmware↔profile contract, fixing both sides, and passing on hardware (24 MB GIF, release asset).

Debug backends (Phase 2)

The verify pipeline is backend-agnostic: flash.adapter: in the board profile picks the probe tool — cubeprogrammer (default, the original implementation), openocd (same ST-Link, no ST toolchain needed, and the standard route to Linux/ARM64 bench hosts like a Raspberry Pi), or fake (scripted, for tests). Validated on the same Apollo board: swapping to openocd is a one-line profile change — verify stays green with identical records, zero upper-layer edits, and runs slightly faster. OpenOCD is discovered via PATH or $OPENOCD_BIN; the target script maps from the MCU family (STM32H7* -> stm32h7x, override with flash.openocd_target).

Board profiles

One yaml per board (boards/): build command, artifact, flash address (flash.adapter: picks the debug backend), serial adapter hints, banner template, probes, watch globs. The console-side USB adapter is a property of your bench, not the board — port resolution goes explicit serial.port / FLASHGATE_SERIAL_PORT, then VID/PID hint, then the sole serial port, with the banner match as the final identity proof. See the guide for the firmware-side integration recipe (three levels, with code) and the full profile field reference.

Status

Boot gate, probe gate, Stop hook, MCP server, SWD signature channel, verification records (per-check evidence with artifact hashes), the remote bench over device-connect (validated cross-host), and a second debug backend (OpenOCD, validated on the same board) — all on real hardware. Windows-first; Linux/macOS untested.

License

MIT

中文说明

flashgate 回答一个很具体的问题：刚编译出来的固件，烧到板子上到底能 不能跑。它把整条链路自动化：编译、ST-Link 烧录、等板子报告身份、经 串口实际调用功能并断言，任何一步断了就以非零退出码结束。

完整的使用说明在 docs/GUIDE.md：接线、安装、第一次 验证、给自己的板子写档案、探针写法、Stop hook 和 MCP 的配置、排错。

要点：

• 板子有两种方式自证：串口 banner，或者在固定 RAM 地址发布 64 字节 签名（后者只靠 ST-Link 就能验证，不用串口线）
• 版本身份带 -dirty 语义，验证通过意味着板上跑的就是当前工作区
• 探针下真命令、断言硬件寄存器读回值；响应报的是实际状态不是回声， 静默失效的设置第一步就会露馅
• 每次验证（无论成败）都留一份证据记录：逐项检查结论、板子的原话、 产物哈希——事后可审计"当时验证的是什么、板子说了什么"
• bench-serve 可以把整个台架挂上局域网：远程 agent 用 device-connect 协议发现它、请求真机验证、拿回带证据的结论（跨机实测通过）
• Stop hook 挂进 Claude Code：agent 改了固件没过真机验证就说"完成"， 会被拦下并收到板子的失败证词；同一棵坏树最多拦两次，之后放行但 打警告，会话不会被卡死
• 仓库带完整的示例固件（examples/apollo-h743），接好线 clone 下来 就能跑通第一次验证

pip install -e ".[mcp]"
flashgate doctor                  # 体检
flashgate verify --all-probes     # 完整验证
echo $?

六个真机演示 GIF 在 demo/，包括一段完整的 Claude Code 会话： agent 改固件、被拦、自己定位到固件与板卡档案的契约不一致、两侧改齐、 真机通过后放行。

MIT License