ingenic-flash-tool 0.5.5

Lightweight CLI tool for flashing Ingenic SoCs via USB boot mode

ingenic-flash-tool

Lightweight Python CLI tool for flashing Ingenic T-series SoCs (T20/T21/T23/T30/T31/T40/T41) via USB boot mode. Supports SPI NOR flash and eMMC.

Installation

pip install ingenic-flash-tool

Requires libusb on your system:

• Linux: sudo apt install libusb-1.0-0 or sudo pacman -S libusb
• macOS: brew install libusb

udev rules (Linux)

To use without sudo, add a udev rule:

echo 'SUBSYSTEM=="usb", ATTR{idVendor}=="a108", MODE="0666"' | sudo tee /etc/udev/rules.d/99-ingenic.rules
sudo udevadm control --reload-rules && sudo udevadm trigger

Usage

Detect device

$ ingenic-flash-tool detect
Device found!
  USB PID:  0xc309 (T-series)
  CPU info: b'T 3 1 V ' (hex: 5420332031205620)

Flash SPI NOR

$ ingenic-flash-tool -v flash prj008 firmware.bin
INFO: Boot ROM CPU info: 5420332031205620
INFO: Loading ginfo (324 bytes) to 0x80001000
INFO: Loading SPL (32384 bytes) to 0x80001800
INFO: SPL running: 5420332031205620
INFO: Loading stage2 (417656 bytes) to 0x80100000
INFO: Stage2 running: b'PRJ\x00\x00\x00\x00\x00'
INFO: Flash JEDEC ID: 0xef7018
INFO: Initializing flash...
INFO: Writing 232652 bytes (227K) at offset 0x0
  [########################################] 100% (232652/232652)
Flash complete!

Flash eMMC

$ ingenic-flash-tool -v flash prj008_mmc0 firmware.bin
INFO: Stage2 running: b'PRJ\x00\x00\x00\x00\x00'
INFO: Initializing flash...
INFO: Writing 232652 bytes (227K) at offset 0x0
  [########################################] 100% (232652/232652)
Flash complete!

Options

• -v / -vv — increase verbosity
• --offset 0x40000 — write at a specific flash offset
• --erase-all — full chip erase before writing (SPI NOR only, default: sector erase)
• --no-reboot — don't reboot the device after flashing

Boot device

Boot into stage2 burner without flashing (useful for debugging):

$ ingenic-flash-tool boot prj008
Device booted into stage2: b'PRJ\x00\x00\x00\x00\x00' (50524a0000000000)

Show chip info

$ ingenic-flash-tool info
Supported chips:
  prj008      PID=0xc309  ginfo=0x80001000 [bundled]
  prj008_mmc0 PID=0xc309  ginfo=0x80001000 [bundled]
  t20         PID=0xc309  ginfo=0x80001000 [bundled]
  ...

Supported Hardware

Board/Target	Flash Type	Status
prj008	SPI NOR	Full support (T31/T33 camera board)
prj008_mmc0	eMMC/SD	Full support (MSC0 slot)
T20–T41	—	Boot only (need board-specific ginfo + config)
40+ chips	—	Bundled SPL/U-Boot for all Ingenic SoCs

Full flash support requires board-specific firmware files (ginfo.bin, spl.bin, uboot.bin, and config blobs). PRJ008 files are bundled for both SPI NOR and eMMC.

How It Works

The tool implements the Ingenic USB boot protocol, reverse-engineered from USB packet captures:

1. Boot ROM — The SoC enters USB boot mode. The tool sends a DDR configuration block (ginfo) and first-stage bootloader (SPL) via vendor USB requests.

2. SPL — The SPL initializes DDR memory, then stays resident and re-implements USB. It does not return to the boot ROM. The tool sends the stage2 burner firmware (U-Boot) via the SPL's USB interface.

3. Stage2 Burner — A specialized U-Boot build that handles flash operations. The tool sends board configuration, then writes firmware in 64KB chunks with CRC verification. Supports SPI NOR (with JEDEC auto-detection), SPI NAND, and eMMC/SD.

Protocol details

Boot ROM requests: GET_CPU_INFO(0x00), SET_DATA_ADDR(0x01), SET_DATA_LEN(0x02),
                   PROGRAM_START1(0x04)
SPL requests:      FLUSH_CACHES(0x03), PROGRAM_START2(0x05)
Stage2 requests:   GET_ACK(0x10), INIT(0x11), WRITE(0x12), UPDATE_CFG(0x14),
                   REBOOT(0x16), GET_FLASH_INFO(0x26)

Key discovery: FLUSH_CACHES and PROGRAM_START2 are only supported by the resident SPL, not the boot ROM (contrary to the JZ4760 documentation). The boot ROM only supports requests 0x00–0x02 and 0x04.

Development

git clone https://github.com/will-tm/ingenic-flash-tool.git
cd ingenic-flash-tool
python -m venv .venv
source .venv/bin/activate
pip install -e .

License

MIT