mcserial 2026.2.12.5

MCP Serial Port Server - FastMCP server for serial port access

MCP Serial Server

FastMCP server for serial port access via Model Context Protocol.

Features

• RS-232 Mode: Full modem control (RTS, DTR, CTS, DSR, RI, CD, break condition)
• RS-422 Mode: Full-duplex differential point-to-point (or 1-to-10 receivers) over long distances
• RS-485 Mode: Half-duplex bus communication with auto direction control
• File Transfer: X/Y/ZMODEM protocols for reliable file transfers
• Auto-baud Detection: Smart detection using 0x55 sync pattern analysis
• URL Handlers: Open remote/virtual ports (socket://, rfc2217://, loop://, spy://, cp2110://)
• Dynamic Resources: Read data via serial://{port}/data
• Full pyserial support (baudrate, parity, stop bits, flow control)

Installation

# With uvx (recommended)
uvx mcserial

# Or install directly
uv pip install mcserial

# With CP2110 HID-to-UART support
uv pip install mcserial[cp2110]

Usage with Claude Code

# Add to Claude Code
claude mcp add mcserial "uvx mcserial"

Modes

Ports open in RS-232 mode by default. Switch with set_port_mode() or pass mode= to open_serial_port():

Mode	Use Case	Tools
RS-232	Point-to-point serial	get_modem_lines, set_modem_lines, pulse_line, send_break
RS-422	Full-duplex differential links	check_rs422_support (plus all common tools)
RS-485	Multi-drop bus (Modbus)	set_rs485_mode, rs485_transact, rs485_scan_addresses

Tools

Common (all modes)

Tool	Description
list_serial_ports	Discover available ports (supports grep regex filtering)
open_serial_port	Open connection — local device or URL scheme (auto-detects baud if not specified)
close_serial_port	Close a connection
set_port_mode	Switch between RS-232, RS-422, and RS-485 modes
write_serial	Send text data
write_serial_bytes	Send raw bytes (atomic single-syscall write)
read_serial	Read available data
read_serial_line	Read until newline
read_serial_lines	Batch read multiple lines
read_until	Read until custom terminator
transact	Send command + read response in one call (any mode)
configure_serial	Change port settings (including default line ending)
flush_serial	Clear buffers
cancel_read	Interrupt pending read operation
cancel_write	Interrupt pending write operation
set_flow_control	Manually gate XON/XOFF or RTS/CTS flow
set_low_latency_mode	Enable kernel low-latency mode (Linux)
get_connection_status	List open connections with mode
detect_baud_rate	Auto-detect baud rate

RS-232 Mode

Tool	Description
get_modem_lines	Read CTS, DSR, RI, CD, RTS, DTR states + break condition
set_modem_lines	Control RTS and DTR outputs
pulse_line	Pulse RTS/DTR for reset sequences
send_break	Send timed break signal
set_break_condition	Hold/release break state

RS-422 Mode

Tool	Description
check_rs422_support	Detect RS-422 adapter capabilities (chip, differential pairs)

RS-485 Mode

Tool	Description
set_rs485_mode	Configure hardware RS-485 (DE/RE control)
check_rs485_support	Detect hardware RS-485 capability
rs485_transact	Send/receive with automatic turnaround
rs485_scan_addresses	Scan bus for responding devices

File Transfer

Tool	Description
file_transfer_send	Send file via XMODEM/YMODEM/ZMODEM
file_transfer_receive	Receive file via XMODEM/YMODEM/ZMODEM
file_transfer_send_batch	Send multiple files (YMODEM/ZMODEM)

Protocols:

• xmodem - 128-byte blocks, simple (1977)
• xmodem1k - 1024-byte blocks
• ymodem - Batch mode with filename/size
• zmodem - Streaming, auto-resume (recommended)

URL Handlers

The open_serial_port tool accepts URL schemes in addition to local device paths:

Scheme	Description	Example
socket://	Raw TCP socket — serial-to-ethernet bridges	socket://192.168.1.100:4001
rfc2217://	Telnet COM Port Control — remote baud/flow config	rfc2217://192.168.1.100:2217
loop://	Loopback — writes echo back as reads (testing)	loop://
spy://	Debug wrapper — logs all traffic to stderr	spy:///dev/ttyUSB0
cp2110://	Silicon Labs HID-to-UART (requires [cp2110] extra)	cp2110://
hwgrep://	Open first port matching hardware pattern	hwgrep://FTDI
alt://	Alternate port backend	alt:///dev/ttyUSB0

URL-opened ports skip auto-baud detection and exclusive access (not applicable to virtual/network ports).

Resources

URI	Description
serial://server/info	Server version, repo links, connection count
serial://ports	List available ports
serial://{port}/data	Read data from open port
serial://{port}/status	Port config and mode
serial://{port}/raw	Read as hex dump
serial://log	Server-wide log buffer
serial://{port}/log	Per-port traffic log (if enabled)

Environment Variables

Variable	Default	Description
MCSERIAL_DEFAULT_BAUDRATE	9600	Default baud rate
MCSERIAL_DEFAULT_TIMEOUT	1.0	Read timeout (seconds)
MCSERIAL_MAX_CONNECTIONS	10	Max concurrent ports

Example Workflows

Basic RS-232

1. list_serial_ports() → find /dev/ttyUSB0
2. open_serial_port(port="/dev/ttyUSB0")  # auto-detects baud
3. configure_serial(port="/dev/ttyUSB0", line_ending="crlf")  # auto-append \r\n
4. transact(port="/dev/ttyUSB0", data="AT")  # send + read in one call
5. close_serial_port(port="/dev/ttyUSB0")

Filter Ports by Hardware

1. list_serial_ports(grep="FTDI")       # find all FTDI devices
2. list_serial_ports(grep="CP210")      # find Silicon Labs adapters
3. list_serial_ports(grep="VID:PID=0403:6001")  # exact USB ID match

RS-422 Differential Link

1. open_serial_port(port="/dev/ttyUSB0", baudrate=9600, mode="rs422")
2. configure_serial(port="/dev/ttyUSB0", line_ending="crlf")
3. transact(port="/dev/ttyUSB0", data="READ TEMP")  # full-duplex, no direction control
4. check_rs422_support(port="/dev/ttyUSB0")

RS-485 Modbus

1. open_serial_port(port="/dev/ttyUSB0", baudrate=9600, mode="rs485")
2. rs485_scan_addresses(port="/dev/ttyUSB0")  # discover devices
3. rs485_transact(port="/dev/ttyUSB0", data="\x01\x03...")

Network Serial (serial-to-ethernet bridge)

1. open_serial_port(port="socket://192.168.1.100:4001", baudrate=115200)
2. write_serial(port="socket://192.168.1.100:4001", data="AT\r\n")
3. read_serial(port="socket://192.168.1.100:4001")

Loopback Testing (no hardware needed)

1. open_serial_port(port="loop://", baudrate=9600)
2. write_serial(port="loop://", data="hello")
3. read_serial(port="loop://")  # → "hello"
4. close_serial_port(port="loop://")

File Transfer

1. open_serial_port(port="/dev/ttyUSB0", baudrate=115200)
2. file_transfer_send(port="/dev/ttyUSB0", file_path="firmware.bin")

License

MIT