nau7802 0.5.1

NAU7802 Driver

NAU7802

A typed, register-accurate Python driver for the NAU7802 24-bit ADC load-cell amplifier.

This library provides a clean, Pythonic interface to the NAU7802 while preserving a 1:1 mapping to the hardware register model. Every register is represented as a strongly-typed dataclass, enabling safe configuration, introspection, and debugging without hiding how the device actually works.

Designed primarily for Linux SBCs (Raspberry Pi, etc.) using I²C via smbus2.

Features

• ✅ Typed register definitions (dataclasses)
• ✅ Full register-level control
• ✅ Automatic byte packing/unpacking
• ✅ Signed 24-bit and 32-bit register support
• ✅ Minimal abstraction — hardware behavior stays visible
• ✅ CLI utility for quick testing and debugging
• ✅ Python 3.11+

Philosophy

Many ADC drivers hide device behavior behind opaque APIs.

nau7802 intentionally does the opposite:

The hardware register map is the API.

Each NAU7802 register is modeled explicitly:

• Bitfields become dataclass fields
• Reads return structured objects
• Writes serialize automatically
• Multi-byte registers behave naturally

This makes debugging with a datasheet straightforward — what you see in Python matches what exists on the chip.

Typed registers prevent invalid bit configurations and make register state inspectable during debugging.

Installation

pip install nau7802[i2c]

Or from source:

git clone https://github.com/jbussdieker/nau7802
cd nau7802
pip install -e .

Requirements

• Python ≥ 3.11
• Linux I²C support enabled
• smbus2

Example (Raspberry Pi):

sudo raspi-config
# Enable I2C

Quick Start

import smbus2
from nau7802 import NAU7802

bus = smbus2.SMBus(1)
adc = NAU7802(bus, addr=0x2A)

adc.power_on()
adc.set_gain(7)
adc.set_channel(1)

print(adc.ctrl2)
# REG_CTRL2(chs=False, crs=3, ...)

value = adc.adco
print(value)

Command Line Interface

A CLI tool is installed automatically:

nau7802 --help

Power On

nau7802 power_on

Initialize Device

nau7802 init --gain 7 --crs 3

Read ADC Value

nau7802 read

Dump All Registers

nau7802 dump

Example output:

NAU7802
  PU_CTRL      REG_PU_CTRL(...)
  CTRL1        REG_CTRL1(...)
  CTRL2        REG_CTRL2(...)
  ADCO         123456
  REV_ID       REG_REV_ID(...)

Register Model

Registers are first-class objects.

Example:

from nau7802.registers import REG_CTRL1

ctrl1 = REG_CTRL1.read(bus, 0x2A)

ctrl1.pga = 7
ctrl1.write(bus, 0x2A)

Benefits

• No manual bit masking
• Self-documenting configuration
• Datasheet alignment
• Safe serialization

Supported Register Types

Byte Registers

Automatically mapped bitfields:

REG_CTRL2(
    chs=False,
    crs=3,
)

Multi-Byte Registers

Signed values handled automatically:

• 24-bit registers (ADCO, OCALx)
• 32-bit registers (GCALx)

Sign extension is applied transparently.

Device API

Power Control

adc.power_on()
adc.standby()
adc.resume()

Configuration

adc.set_gain(7)
adc.set_crs(3)
adc.set_channel(1)

Reading Data

value = adc.adco

Architecture Overview

nau7802/
├── device/
│   ├── power.py        # power sequencing
│   └── setting.py      # configuration helpers
│
├── register/
│   ├── _base.py        # generic register interface
│   └── _byte.py        # 8-bit register specialization
│
└── registers/
    └── REG_*           # typed register definitions

Layering

1. Register layer — serialization + hardware truth
2. Device layer — safe operations & sequencing
3. CLI layer — human interaction

Example: Debugging With Registers

print(adc.ctrl2)

Instead of raw hex values, you see structured state:

REG_CTRL2(chs=False, crs=3, cal_err=False, ...)

Development

Install dev dependencies:

pip install -e .[dev]

Type checking:

mypy src/

Status

Development Status: Pre-Alpha

The API may change as hardware behavior and ergonomics are refined.

Contributing

Issues and pull requests are welcome:

https://github.com/jbussdieker/nau7802/issues

License

MIT License

Author

Joshua B. Bussdieker [e-mail]