OEP Python client

日本語

The host side of Open Embedded Probe (OEP). It speaks the v1 protocol of oep-spec (docs/oep-core.ja.md and the standard interfaces docs/oep-if-*.ja.md, a candidate being settled). The wire numbers come from oep_client.registry, a verbatim copy of oep-spec's generated generated/oep-v1/oep_v1_registry.py. This is an experimental stage: breaking changes are expected and no compatible API is promised. For a map of the specification, start with oep-spec's docs/review-guide.ja.md.

It follows OEP's division of work: the knowledge of the target lives in the host. The probe knows only its wires and DMI / DP-AP transfers; the CH32 flash controller, the RAM loader, the RP2350 boot ROM, the Cortex-M debug registers and so on are here.

pip install oep-client-python     # PyPI (import oep_client); a checkout: pip install -e <checkout>
uv run pytest                     # in a checkout

import oep_client is all it takes. The registry is copied from oep-spec with tools/sync_registry.sh. PyPI's oep-client is another project, so the distribution is named oep-client-python.

Releases: run the GitHub Actions workflow Release (workflow_dispatch, version X.Y.Z or X.Y.ZbN). tools/prepare_release.py sets the version in pyproject.toml, uv.lock and oep_client.__version__ and turns CHANGELOG.md's Unreleased into that version; after the tests and the build it commits, tags, makes the GitHub Release and publishes to PyPI (Trusted Publishing). Record changes under Unreleased in CHANGELOG.md, (EN) and (JA).

Modules (oep_client)

Example

from oep_client import core, link, riscv, ch32_flash

hst = link.open_host("/run/board-identify/by-id/esp32-series-30eda0e31108")   # pipelined
# a serial port (always COBS), "tcp://127.0.0.1:PORT" (a broker), "usb" / "usb:303a:0002[:SERIAL]" (vendor, then HID)
core.take(hst, 30000, owner="flash script")   # the only way in: force; else wait out the lease, name the holder
wire = riscv.Wire(hst, "oep.wire.rvswd")
conn, _ = wire.attach(halt=True)
dm = riscv.RiscvDm(hst, conn)
dm.reset_halt()
result = ch32_flash.program(hst, dm, open("sketch.bin", "rb").read(), ch32_flash.PROFILES["x035"])
dm.reset(confirm=True)
wire.detach(conn)
hst.end()

The oep command

oep dump --port <probe>                      # what the probe offers (--fake p4-x035: no hardware)
oep config show <probe>                      # the settings and the live slot / bind state
oep config slot <probe> --name x035 --wire rvswd --pins 2,54 --attach at-boot --retry 1 --mechanism dmseq
oep config bind <probe> --port 1 --mode last-reset --stream slot:x035
oep config save <probe>                      # kept over a restart (also: remove, erase)

<probe> is a serial port, tcp://HOST:PORT or usb[:VID:PID[:SERIAL]]. A change takes the lock (owner "oep config") and ends the session after it; it takes effect at once and, after save, stays over a restart.

A run on hardware: ArduinoCore-CH32's tests/manual/oep_smoke/ (oep_smoke.py, oep_probe_checks.py).

The fake probe (a working spec)

endpoint.Endpoint is a fake probe that answers as oep-spec says; ch32rv, this client and the probe firmware are checked against it (when the spec changes, this is brought in line before the firmware). fake holds example declarations (profiles p4-x035, esp32-v003, p4-bench = a made-up jig with three slots and two seats, rp2350-pins = a wire whose pins the host chooses), fake_serial the byte side of a serial port (COBS candidates, raw bytes and binds, held during a session and resumed after it).

fake_capture is oep.fixture.capture (logic): one-shot, repeat (segments with the clock at the actual rate, a ring, release) and streaming (data pushes while subscribed), level / edge triggers with a pretrigger, and events. What it captures is known: sample i is the counter i, channel k its bit k (a square wave of period 2^(k+1) samples), in the layout the profile allows (p4-x035: w 1-16 as the P4's PARLIO, three channels in w 4; esp32-v003: w 8 as the classic ESP32's sampler, one-shot only). A capture only listens, so it may be planned on pins other interfaces hold. p4-x035 also has oep.fixture.analog (4 channels of the P4's ADC1 on GPIO16-23: an even channel k a square wave, an odd one a sine, of period 64 (k // 2 + 1) samples, 12-bit values in 16-bit slots; ESP32-style frontends; a made-up two-point calibration and a Vrefint) and oep.fixture.capture-group binding the logic and the analog: started together, the analog 5 us later (+-2 us), the trigger of one marked on both. Times are ns on the probe's one clock.

Other programs' tests run fake_serve as a child process:

python -m oep_client.fake_serve --pty --profile p4-bench --slot x035 --bind last-reset \
    --console 'uptime %d\r\n' --every 100
# first line: PTY /dev/pts/N (PORT n with --tcp 0); it ends when stdin closes

The pty is a serial port (the host opens it with TIOCEXCL); --tcp PORT is --framing cobs (a serial port) or --framing length (the vendor bulk / TCP form). Faults: --drop N (the N-th answer is not sent, once; the request did run, so a resend gets the remembered result), --noise TEXT (noise before every answer), --corrupt N (the N-th answer's CRC broken once). --uart-plan / --uart-rx give the first fixture UART a plan and RX bytes, --run-hook a host's own model of riscv-dm run, --capture-slipped flags bit2 on every capture segment. Events and data pushes go out on the pty and on TCP (both framings). The rest: --help.