podman-spawner 0.2.0

a Podman interface for container management

Podman Spawner — a Podman interface for container management

podman-spawner automates the creation and lifecycle management of Podman containers, easing the creation of temporary podman images.

It was originally developed to review students projects, enabling to create containers on the fly for each student group and submission version.

Table of contents

• Prerequisites
• Using pod

---

Prerequisites

pod is a thin wrapper around Podman (a rootless Docker alternative). Install it before anything else:

sudo apt install podman containers-storage

containers-storage is not strictly required, but it switches the storage driver from vfs to overlay, which makes image builds significantly faster. Verify it worked:

podman info | grep graphDriverName   # should print: overlay

To pull images from Docker Hub, register it as an unqualified search registry:

mkdir -p ~/.config/containers/
echo 'unqualified-search-registries = ["docker.io"]' >> ~/.config/containers/registries.conf

For a small Podman introduction, see podman-intro.md.

---

Using pod

Installation

Install uv if you do not have it already:

curl -LsSf https://astral.sh/uv/install.sh | sh

Then, from the root of the pod repository:

uv tool install -e .

The pod command is now available for the current user.

Configuration

Every pod command reads config.toml from the current working directory. A default file is created by pod init (see below); its keys are:

Key	Default	Description
prefix	POD	Prefix prepended to every container name.
port	2026	Guest port exposed by the container.
user	tester	Username created inside the container at build time.

Workflow overview

pod init        # create the pod-build/ scaffold
  ↓ (edit Dockerfile, home-dir/, on_build.bash as needed)
pod build       # build the Podman image
pod test        # smoke-test the image interactively
  ↓
pod go <name>   # open a container for a group / version

Commands

pod init

Creates a pod-build/ directory in the current directory (or uses the current directory itself if it is already named pod-build), populated with a default Dockerfile, config.toml, on_build.bash, and home-dir/.

pod init                      # create pod-build/ (fails if it already exists)
pod init --force              # overwrite an existing pod-build/
pod init --update Dockerfile  # refresh only one file, keeping local changes

pod build

Builds the Podman image from the pod-build/ directory. Must be run from inside pod-build/ (or a directory that contains it).

pod build

The image is tagged <prefix>:latest (lower-cased), e.g. pod:latest.

pod test

Starts the dedicated test container (<prefix>-test-0.0) and attaches to it interactively. Use this to verify that a freshly built image behaves correctly before deploying it to students. The container is created if it does not exist.

pod test

pod go <name>

Attaches to a container, creating or restarting it as needed.

pod go GROUP-1.0

The host port is derived deterministically from the container name, so the same container always gets the same port across restarts.

pod list

Lists all containers belonging to this project (filtered by prefix).

pod list

pod info <name>

Prints the state and port-forwarding details of a container.

pod info GROUP-1.0

pod rm <name>

Removes a container permanently.

pod rm GROUP-1.0           # fails if the container is still running
pod rm GROUP-1.0 --force   # stops and removes unconditionally

Note: due to a limitation in python-fire, --force must come after the container name.

pod purge <regex>

Removes all containers whose full name matches regex (matched with re.fullmatch, i.e. the pattern must cover the entire name including the prefix).

pod purge 'POD-GROUP-1.*'           # remove all versions for GROUP-1
pod purge 'POD-GROUP-1.*' --force   # also remove running containers

pod purge-all

Removes every container belonging to this project, including the test container.

pod purge-all
pod purge-all --force