pttman 0.3.1

Push-to-talk microphone control with a daemon-backed command queue

pttman

Push-to-talk microphone control for PipeWire.

pttman runs a small user service that serializes mute, unmute, and toggle requests over a Unix datagram socket so rapid key presses do not race each other.

Requirements

• PipeWire with PulseAudio compatibility (pipewire-pulse)
• pactl (from pipewire-pulse or pulseaudio-utils)
• systemctl (for set-default-source to signal the daemon)

Installation

Recommended: uv

uv tool install pttman
pttman install-service
systemctl --user start pttman.service

This installs pttman to ~/.local/bin/, copies the systemd user service into place, and enables it. After installing, point your push-to-talk key at the client binary.

Alternative: install.sh

git clone https://github.com/mwolson/pttman.git
cd pttman
./install.sh
systemctl --user start pttman.service

This copies pttman to ~/.local/bin/ and installs and enables the user service.

Optional: set defaults

By default, pttman operates on all audio sources. You can optionally save a preferred source so that pttman controls only that one:

pttman list-sources
pttman set-default-source alsa_input.usb-046d_BRIO-03.pro-input-0

This writes to ~/.config/pttman.conf and signals the running daemon to pick up the change.

xremap

On Arch Linux, install the xremap variant that matches your desktop environment (only one should be installed):

paru -S xremap-gnome-bin     # GNOME
paru -S xremap-hyprland-bin  # Hyprland
paru -S xremap-kde-bin       # KDE Plasma
paru -S xremap-niri-bin      # Niri
paru -S xremap-wlroots-bin   # wlroots-based compositors (sway, etc.)

Then configure a push-to-talk key binding:

modmap:
  - name: Push-to-talk
    remap:
      F6:
        skip_key_event: true
        press: { launch: ["/home/your-user/.local/bin/pttman", "unmute"] }
        release: { launch: ["/home/your-user/.local/bin/pttman", "mute"] }

Pressing F6 (as configured above, which is conveniently labeled with a mic icon on some laptop keyboards) tells the daemon to unmute. Releasing F6 tells it to mute again.

You can also route your compositor's mic-mute key through pttman. For example, in niri's keybinds.kdl this implements mic toggle (rather than push-to-talk):

XF86AudioMicMute  allow-when-locked=true { spawn "/home/your-user/.local/bin/pttman" "toggle"; }

You can check the current microphone state with:

pttman status

Corsair mice on Arch Linux

If you use a Corsair mouse and want one of its extra buttons to behave like F6, ckb-next is a straightforward way to do it.

On Arch Linux, install ckb-next with:

sudo pacman -S ckb-next

Then launch ckb-next, select your mouse, pick the button you want to use for push-to-talk, and remap that button to F6.

After that, xremap can keep using the F6 rule above, and your Corsair mouse button will trigger push-to-talk through pttman.

If you specifically want the upstream development build instead of the packaged release, the ckb-next project wiki also lists ckb-next-git for Arch-based systems.

Commands

pttman uses subcommands for one-off operations. With no subcommand, it runs the daemon.

pttman                                 Run the daemon (default)
pttman get-default-source              Print the default source from the config file
pttman install-service                 Install and enable the systemd user service
pttman list-sources                    List available audio sources
pttman mute                            Mute the microphone
pttman set-default-source SOURCE       Save default source and signal the daemon
pttman status                          Print the current microphone state
pttman toggle                          Toggle the microphone mute state
pttman uninstall-service               Disable and remove the systemd user service
pttman unmute                          Unmute the microphone

Aliases:

• release for mute
• press and talk for unmute

Options

These flags apply to the daemon and to action commands (mute, unmute, toggle, status):

--source SOURCE     Audio source name to control (default: config file, then all sources)
--all-sources       Operate on all audio sources (overrides --source from config)

--source and --all-sources are mutually exclusive.

Configuration File

pttman reads defaults from ~/.config/pttman.conf (or $XDG_CONFIG_HOME/pttman.conf). The file uses one flag per line:

--source=alsa_input.usb-046d_BRIO-03.pro-input-0

Supported flags:

• --source=NAME -- control only this source
• --all-sources=true -- control all sources (the default when no config file exists)

These are mutually exclusive. Unrecognized flags cause an error at startup. Command-line arguments always take precedence over the config file.

When the daemon receives a SIGHUP (sent automatically by set-default-source, or manually via systemctl --user reload pttman.service), it reloads the config file and updates the source for future operations.

Service

systemctl --user start pttman.service
systemctl --user status pttman.service
journalctl --user -u pttman.service -f

The daemon listens on $XDG_RUNTIME_DIR/pttman.sock. If the daemon is not running, client commands fall back to direct pactl execution.

Development

Testing

python3 -m unittest discover -s tests -v

Hooks

lefthook install
lefthook run pre-commit --all-files

The pre-commit hook runs uvx ruff check, uvx ty check, and the unit test suite.

License

MIT