ptw 0.4.1

Pooling TLS Wrapper

ptw

Pooling TLS Wrapper

Accepts TCP connections on listen port and forwards them, wrapped in TLS, to destination port. ptw maintains pool of fresh established TLS connections effectively cancelling delay caused by TLS handshake.

ptw may serve as drop-in replacement for stunnel or haproxy for purpose of secure tunneling of TCP connections. Thus, it is intended for use with stunnel or haproxy on server side, accepting TLS connections and forwarding them, for example, to SOCKS proxy. In such configuration make sure your server timeouts long enough to allow fit lifetime of idle client TLS sessions (-T option).

ptw can be used with custom CAs and/or mutual TLS auth with certificates.

Requirements

• Python 3.5.3+

Installation

pip3 install ptw

Usage

See quickcerts for easy TLS certificate generator.

Wrapper for SOCKS/HTTP proxy

ptw -c mycert.pem -k mykey.pem -C ca.pem -n 50 -T 300 example.com 1443

Corresponding haproxy configuration on server:

...

defaults
    log       global
    mode      tcp
    option    tcplog
    option    dontlognull
    timeout connect 5000
    timeout check   5000
    timeout client  600000
    timeout server  600000
    timeout tunnel  600000

frontend socks-proxy
    bind *:1443 ssl crt /etc/haproxy/server.combined.pem ca-file /etc/haproxy/ca.pem verify required
    default_backend socks-proxy

backend socks-proxy
    server localsocks 127.0.0.1:1080

This command will accept TCP connections on port 57800, wrap them in TLS and forward them to port 1443 of example.com host, maintaining pool of at least 50 TLS connections no older than 300 seconds. For client TLS authentication see also -c and -k options.

Transparent proxy for TCP connections

Run on your router:

ptw -a 0.0.0.0 -c mycert.pem -k mykey.pem -C ca.pem -n 50 -T 300 -P v1 example.com 2443

Add following rule to iptables:

iptables -I PREROUTING 1 -t nat -p tcp -s 192.168.0.0/16 '!' -d 192.168.0.0/16 -j REDIRECT --to 57800

Assuming your local network is covered by prefix 192.168.0.0/16.

Corresponding haproxy config sections:

frontend tls-wrapper
    bind *:2443 ssl crt /etc/haproxy/server.combined.pem ca-file /etc/haproxy/ca.pem verify required
    default_backend strip-proxy

backend strip-proxy
    server strip-proxy 127.0.0.1:41718

frontend strip-proxy
    bind 127.0.0.1:41718 accept-proxy
    default_backend passthrough

backend passthrough
    server direct *

This setup will redirect all TCP connections in your network. If your server supports proxy protocol version 2, you may use it as well (option -P v2).

Synopsis

$ ptw --help
usage: ptw [-h] [-v {debug,info,warn,error,fatal}] [-l FILE]
           [--disable-uvloop] [-a BIND_ADDRESS] [-p BIND_PORT]
           [-P {none,v1,v2}] [-n POOL_SIZE] [-B BACKOFF] [-T TTL] [-w TIMEOUT]
           [-c CERT] [-k KEY] [-C CAFILE]
           [--no-hostname-check | --tls-servername TLS_SERVERNAME]
           dst_address dst_port

Pooling TLS wrapper

positional arguments:
  dst_address           target hostname
  dst_port              target port

optional arguments:
  -h, --help            show this help message and exit
  -v {debug,info,warn,error,fatal}, --verbosity {debug,info,warn,error,fatal}
                        logging verbosity (default: info)
  -l FILE, --logfile FILE
                        log file location (default: None)
  --disable-uvloop      do not use uvloop even if it is available (default:
                        False)

listen options:
  -a BIND_ADDRESS, --bind-address BIND_ADDRESS
                        bind address (default: 127.0.0.1)
  -p BIND_PORT, --bind-port BIND_PORT
                        bind port (default: 57800)
  -P {none,v1,v2}, --proxy-protocol {none,v1,v2}
                        transparent mode: prepend all connections with proxy-
                        protocol data (default: none)

pool options:
  -n POOL_SIZE, --pool-size POOL_SIZE
                        connection pool size (default: 25)
  -B BACKOFF, --backoff BACKOFF
                        delay after connection attempt failure in seconds
                        (default: 5)
  -T TTL, --ttl TTL     lifetime of idle pool connection in seconds (default:
                        30)
  -w TIMEOUT, --timeout TIMEOUT
                        server connect timeout (default: 4)

TLS options:
  -c CERT, --cert CERT  use certificate for client TLS auth (default: None)
  -k KEY, --key KEY     key for TLS certificate (default: None)
  -C CAFILE, --cafile CAFILE
                        override default CA certs by set specified in file
                        (default: None)
  --no-hostname-check   do not check hostname in cert subject. This option is
                        useful for private PKI and available only together
                        with "--cafile" (default: False)
  --tls-servername TLS_SERVERNAME
                        specifies hostname to expect in server TLS certificate
                        (default: None)