python-can-flexible-serial 0.1.1

python-can interface plugin for a configurable binary serial CAN protocol

python-can-flexible-serial

A python-can interface plugin that speaks a configurable, framed binary protocol over a serial port. It follows the python-can plugin interface, so once installed it is usable anywhere python-can accepts an interface= name — can.Bus, python -m can.viewer, python -m can.logger, python -m can.bridge, etc. — alongside the other community interface plugins listed on that page (python-can-canine, python-can-cvector, python-can-remote, python-can-sontheim, python-can-cando, python-can-candle, ...).

Unlike the fixed-layout slcan and serial interfaces bundled with python-can, the frame layout here is configurable via constructor kwargs (SOF/EOF delimiters, ID width, optional CRC, optional flags byte, optional timestamp) so it can be adapted to match firmware on the other end of the serial link without changing code.

Frame layout

Section	Field	Size	Optional / Configurable
—	SOF	1+ bytes	Configurable delimiter (default 0xAA)
Header	timestamp	0 or 4 bytes	Optional — omitted when no_timestamp=True
Header	dlc	1 byte	Always present
Header	flags	0 or 1 byte	Optional — only present when flags_byte=True
Header	id	2 or 4 bytes	Sizeable — 2 bytes when uint16_id=True, else 4
Payload	data	0-64 bytes	Sizeable — length equals dlc
—	crc	0 or N bytes	Optional — size/presence set by crc_type
—	EOF	1+ bytes	Configurable delimiter (default 0xBB)

Details on each section:

• SOF / EOF — arbitrary-length byte sequences used purely as framing delimiters. They are never covered by the CRC.
• timestamp (optional, fixed 4 bytes when present) — uint32 milliseconds. Omit entirely with no_timestamp=True to save 4 bytes per frame if the far end doesn't supply/need one; python-can still assigns a local receive timestamp in that case.
• dlc (always present, fixed 1 byte) — raw payload length in bytes; also used to size the data section on receive.
• flags (optional, fixed 1 byte when present) — see "Flags byte" below for the bit layout. When absent, the same metadata is instead packed into spare bits of the id field (see below).
• id (always present, sizeable: 2 or 4 bytes) — arbitration ID. uint16_id=True shrinks it to 2 bytes but rejects extended (29-bit) IDs; the default 4-byte field supports both standard and extended IDs.
• data (sizeable, 0-64 bytes) — the CAN payload; length is whatever dlc says, up to 64 bytes for CAN FD-sized frames or 8 bytes otherwise.
• crc (optional, sizeable: 0 or N bytes) — set by crc_type ("none" or "crc16-ccitt"); covers the header and payload, but not SOF/EOF.

Byte order for the header and CRC fields is little-endian by default, or big-endian when big_endian=True.

Flags byte

When flags_byte=True, extended/error/remote/FD metadata is carried in a dedicated byte instead of being packed into spare bits of the arbitration ID:

Bit	Mask	Meaning
0	0x01	Error frame
1	0x02	Remote frame (RTR)
2	0x04	Extended (29-bit) ID
3	0x08	CAN FD frame
4	0x10	CAN FD bit-rate switch
5	0x20	Frame originated as RX (vs. TX)

When flags_byte=False, extended/error/remote status is instead OR'd into spare high bits of the 32-bit arbitration ID field (standard python-can convention: CAN_EFF_FLAG, CAN_ERR_FLAG, CAN_RTR_FLAG). This only applies when uint16_id=False, since a 16-bit ID field has no spare bits for flags.

Error frames

Protocol-level errors (frame desync, bad DLC, EOF mismatch, bad CRC) are surfaced as Message objects with is_error_frame=True rather than raising exceptions, matching how other python-can interfaces report bus errors. Use FlexibleSerial.decode_serial_can_error(msg) to get a human-readable description of an error message's contents.

Installation

How you install this depends on whether you're using it as a dependency of some other project, or working on this repo itself.

Using this plugin from another project

If that project is managed with uv, add this repo as an editable path dependency, pointing at wherever you've cloned it:

uv add --editable plugins/python-can-flexible-serial

Run this from that project's directory, not from within this repo — uv add adds a dependency to the project in your current directory, so running it from inside python-can-flexible-serial itself is a self-dependency and uv will refuse it.

With plain pip, from that project's environment:

python -m pip install -e /path/to/python-can-flexible-serial

Working on this repo itself

Use uv sync (a uv-managed project installs itself editable by default):

uv sync

Or with plain pip, from this repo's root:

python -m pip install -e .

Either way, this registers the plugin with python-can via the can.interface entry point (flexible_serial = "flexible_serial.bus:FlexibleSerial"), so it becomes available as interface="flexible_serial" anywhere python-can resolves interfaces, without any further imports.

Usage

import can

bus = can.interface.Bus(
    interface="flexible_serial",
    channel="COM3",
    baudrate=115200,
)

Constructor arguments

Argument	Type	Default	Description
channel	str	(required)	Serial device, e.g. "COM3" or "/dev/ttyUSB0"
baudrate	int	115200	Serial baud rate
timeout	float	0.1	Serial read timeout, in seconds
rtscts	bool	False	Enable RTS/CTS hardware handshake
sof	bytes | hex str	0xAA	Start-of-frame delimiter
eof	bytes | hex str	0xBB	End-of-frame delimiter
big_endian	bool	False	Byte order for header/CRC fields
uint16_id	bool	False	Use a 2-byte arbitration ID instead of 4-byte; rejects extended IDs
flags_byte	bool	False	Carry frame metadata in a dedicated byte (see "Flags byte" above)
no_timestamp	bool	False	Omit the 4-byte timestamp header field
crc_type	str	"none"	One of "none", "crc16-ccitt"
rx_bytes_callback	Callable[[bytes, bool], None] | None	None	Called with (raw_bytes, is_rx) whenever a frame is sent or a chunk of buffer is consumed on receive; useful for logging/debugging the raw wire traffic

sof and eof accept either raw bytes (when constructing a Bus from Python) or a hex string (when passed as a CLI --bus-kwargs value, since python-can CLI tools pass kwargs as strings):

python -m can.logger -i flexible_serial -c COM3 --bus-kwargs sof=0xAA eof=0x0D0A

Prefer the 0x prefix for CLI hex values, especially if the delimiter contains only digits, since python-can auto-converts bare numeric kwargs.

CLI examples

python -m can.viewer -i flexible_serial -c COM6 --bus-kwargs sof=0x4040 eof=0x0A uint16_id=True crc_type=crc16-ccitt flags_byte=False no_timestamp=True

Bridging to another interface:

python -m can.bridge --bus1-interface flexible_serial --bus1-channel COM7 --bus1-bus-kwargs sof=0x4040 eof=0x0A uint16_id=True crc_type=crc16-ccitt flags_byte=False no_timestamp=True --bus2-interface kvaser --bus2-channel 0 --bus2-bitrate 125000

Autodetection

Like the built-in serial interface, available serial ports are surfaced through python-can's autodetection API:

import can
print(can.detect_available_configs(interfaces=["flexible_serial"]))

Layout

python-can-flexible-serial/
  pyproject.toml
  README.md
  src/
    flexible_serial/
      __init__.py
      bus.py
  tests/
    test_hex_bytes.py
    test_bus.py
    message_helper.py

Development

Install with the dev extra to pull in test dependencies (pytest):

uv sync --extra dev

or

python -m pip install -e .[dev]

Run the test suite with:

uv run -m pytest

or

python -m pytest

tests/test_bus.py scaffolds round-trip tests against two backends — a fully in-memory mocked serial port and pyserial's loop:// — mirroring the structure of python-can's own serial interface test suite. The test bodies are currently stubs (skipTest); fill them in as coverage is added.

Future improvement ideas

• can_filters support — already works today for free: BusABC.recv() always calls _matches_filters() in software unless _recv_internal reports the message as pre-filtered, and this interface never does. What's still missing is a hardware-style optimization: implement the optional _apply_filters() hook so frames can be dropped before the CRC check runs, instead of always paying the full decode+CRC cost and filtering afterward.
• Support the CAN FD protocol for the BusABC parent (can_protocol currently reports CAN_20 unconditionally).
• Add an option for arbitrary (non-CAN) data length up to 255 bytes, since dlc is only 1 byte — useful for passing arbitrary serial payloads through python-can tooling without being constrained to CAN/CAN FD payload sizes.