rpi-hwid — Raspberry Pi hardware identity

What is this Raspberry Pi wearing, what powers it, and what is soldered to it? rpi-hwid answers from the Pi itself, using evidence the firmware and kernel already expose but nothing collects: HAT ID EEPROMs (including the ones the firmware never reads), the Pi 5's own verdict on its USB-C supply, the PMIC's input and RTC-cell voltages, the fan header, the USB tree, and which network interfaces are soldered down.

Around that probe:

• a separate FPGA probe for a NeTV2, Acorn or Arty board attached to the Pi,
• a collector that runs both over ssh across a fleet, one JSON document per host,
• names derived from each board's immutable identifier,
• a label generator that turns the documents into sticker sheets carrying only what cannot change: serial numbers, MAC addresses, Device DNA.

Contents

• Install
• Quick start
• The probe: what each signal proves
• FPGA boards
• Collecting a fleet
• The document
• Names
• Labels
• Using it from Python
• Development

Install

uv tool install 'rpi-hwid[labels]'     # everything, including the label generator
pip install rpi-hwid                   # probe, collector, names: no dependencies at all

The probe itself is one dependency-free file that runs on any Pi with python3 3.5 or later, so nothing needs installing on the Pi. Send it over ssh with the source on stdin:

ssh pi@host 'python3 -' < src/rpi_hwid/probe.py
ssh pi@host 'python3 - --json' < src/rpi_hwid/probe.py

On the Pi it wants i2c-tools and passwordless sudo (for i2cdetect, i2ctransfer, dtparam and vcgencmd). Without them it still reports what it can.

Quick start

On a Pi 5 powered through a PoE splitter, with a USB Ethernet adapter:

$ rpi-hwid probe
Raspberry Pi 5 Model B Rev 1.0  serial d88100008543dc30  rev c04170
  header : nothing identifiable on the header
  signal : USB-C as the firmware sees it: max_current 900 mA, no PD contract; 5 V input 4.83 V
  signal : fan header: disabled
  signal : RTC battery: none (0.00 V)
  signal : power port: throttled=0x0
  power  : external supply on USB-C advertising 900 mA by resistor: a PoE splitter or a USB-A lead
  onboard: eth    2c:cf:67:16:bd:98  macb
  onboard: wlan   2c:cf:67:16:bd:99  brcmfmac
  usb net: 0b95:1790 ASIX Elec. Corp. AX88179  00:0e:c6:82:b5:e1  ethernet

On a Pi Zero W wearing Waveshare's PoE-ETH-USB-HUB-HAT bonnet, which has no ID EEPROM and is recognised from the USB tree instead:

$ rpi-hwid probe
Raspberry Pi Zero W Rev 1.1  serial 000000005157f671  rev 9000c1
  header : Waveshare PoE-ETH-USB-HUB-HAT (1a40:0101 hub with RTL8152 on port 4)
  signal : power port: throttled=0x0
  power  : PoE through the Waveshare PoE-ETH-USB-HUB-HAT bonnet
  onboard: wlan   b8:27:eb:02:a3:24  brcmfmac
  usb net: 0bda:8152 Realtek USB 10/100 LAN  00:e0:4c:36:0b:0a  ethernet

The whole command line:

rpi-hwid probe [--json] [--fpga] [--jtag] [--flash]   on a Pi: what is this?
rpi-hwid fpga [--json] [--jtag] [--flash]             on a Pi: which FPGA board?
rpi-hwid collect --out DIR [-J JUMP] [--fpga] HOST…  over ssh: one JSON per host
rpi-hwid labels --data DIR --out labels.pdf           print-ready labels from that data
rpi-hwid name --netv2 DNA… | --arty SERIAL…           the derived board names
rpi-hwid revision CODE…                               decode Pi revision codes

$ rpi-hwid revision c04170 9000c1 a020d3
c04170: Raspberry Pi 5, 4 GB, Rev 1.0, BCM2712
9000c1: Raspberry Pi Zero W, 512 MB, Rev 1.1, BCM2835
a020d3: Raspberry Pi 3 Model B+, 1 GB, Rev 1.3, BCM2837

The probe: what each signal proves

The verdict names the power source where the evidence allows, and says so where it does not:

The switch-side 802.3af class narrows the ambiguous cases (the bonnet is class 3, the M.2 HAT+ (B) class 4, an af-only HAT is never class 4), but that is read from the switch, not the Pi, so it is outside this package.

FPGA boards

rpi_hwid.fpga is kept apart from the Pi probe because few people have an FPGA board on their Pi. rpi-hwid probe --fpga appends it; rpi-hwid fpga runs it alone.

From what the Pi sees without touching the FPGA: a NeTV2 running LitePCIe is PCIe 10ee:7024 with one 1 MiB BAR; an SQRL Acorn CLE-215+ is 1e24:021f (or 10ee:7011 under other gateware) with 128 KiB + 64 KiB BARs; a Digilent Arty is its own FT2232 with a 210319… serial. BAR sizes come from sysfs and a BAR is never mapped, because that wedges a host.

With --jtag, openFPGALoader reads the IDCODE and Device DNA over the Arty's FT2232 or the host's GPIO harness (libgpiod, pins 27:22:4:17). A GPIO chain that answers on a host with no Arty is taken to be a NeTV2. With --flash, an Arty's SPI flash is identified by JEDEC id, which reloads the FPGA with openFPGALoader's bridge bitstream. The S25FL128S and S25FL127S both answer 0x012018, so the label says S25FL128S/127S.

$ rpi-hwid fpga --jtag          # a Pi 4 with an Arty A7-35T on USB
  fpga   : arty (Digilent FT2232 210319B301DE; FT2232 JTAG idcode 0x362d093 artix a7 35t), DNA 0x00628502251ea85c
$ rpi-hwid fpga                 # a Pi 5 with an Acorn on its PCIe connector
  fpga   : acorn (PCIe 1e24:021f, 128 KiB + 64 KiB BARs (SQRL Acorn CLE-215+))

Collecting a fleet

rpi-hwid collect pushes the probe source to each host over ssh (nothing is installed on the Pi), in parallel, and writes <host>.json per host. The FPGA module is appended with --fpga for every host, or with --jtag HOST and --flash HOST for the hosts that should drive JTAG. A login banner before the JSON is skipped.

$ rpi-hwid collect --out data/ -J jump.example.org --fpga --jtag pi@10.21.2.16 \
      rpi5-netv2 rpiz-serial pi@10.21.2.16 pi@10.21.2.47
  rpi5-netv2: Raspberry Pi 5 Model B Rev 1.0; header bare; power usbc-supply
  rpiz-serial: Raspberry Pi Zero W Rev 1.1; header ['Waveshare PoE-ETH-USB-HUB-HAT']; power bonnet-poe
  pi@10.21.2.16: Raspberry Pi 4 Model B Rev 1.5; header ['Pmod HAT Adaptor']; power undetermined; fpga 0x00628502251ea85c
  pi@10.21.2.47: Raspberry Pi 5 Model B Rev 1.1; header ['Waveshare PoE M.2 HAT+ (B)']; power gpio-poe-hat; fpga acorn
4 of 4 host(s) written to data

--users lists the login names to try in order (default: you, then pi); the one that worked is recorded in the document. A host that cannot be reached is reported and skipped, and the exit status says so.

The document

rpi-hwid probe --json, and every file the collector writes, is one JSON object: the raw evidence as it came off the Pi, plus a verdict block with a fixed-shape summary that everything else in the package consumes.

{
  "model": "Raspberry Pi Zero W Rev 1.1",
  "serial": "000000005157f671",
  "revision": "9000c1",
  "hat_fw": null,
  "hat_eeproms": {},
  "i2c1": [],
  "usb": {"1-1": "1a40:0101", "1-1.4": "0bda:8152"},
  "interfaces": ["…"],
  "usb_net": ["…"],
  "throttled": "0x0",
  "verdict": {
    "header": ["Waveshare PoE-ETH-USB-HUB-HAT (1a40:0101 hub with RTL8152 on port 4)"],
    "power": "PoE through the Waveshare PoE-ETH-USB-HUB-HAT bonnet",
    "evidence": ["power port: throttled=0x0"],
    "summary": {
      "model": "Raspberry Pi Zero W Rev 1.1",
      "serial": "000000005157f671",
      "revision": "9000c1",
      "header": ["Waveshare PoE-ETH-USB-HUB-HAT"],
      "hat_uuid": null,
      "power_class": "bonnet-poe",
      "macs": [{"kind": "eth", "mac": "00:e0:4c:36:0b:0a"},
               {"kind": "wlan", "mac": "b8:27:eb:02:a3:24"}],
      "usb_net": [],
      "rtc_battery": null, "fan": null, "max_current_ma": null, "ext5v_v": null,
      "fpga": []
    }
  }
}

(Lists shortened.) The summary is the contract. header is what sits on the 40-pin header, macs the soldered-down interfaces (eth first), usb_net the removable adapters with their descriptors, fpga the boards the FPGA module found, and hat_uuid the EEPROM's UUID when one was read. The Pi 5-only fields are null elsewhere. Everything outside verdict is evidence, kept so a wrong verdict can be argued with.

Names

Raw identifiers come in near-identical clusters (Device DNAs sharing most of their digits, Digilent serials differing in the last byte), so rpi-hwid name hashes them into short, distinct words:

$ rpi-hwid name --netv2 0x00742c4e63b9085c --arty 210319B301DE 210319B0C238
netv2-grove  00742c4e63b9085c
arty-hawk  210319B301DE
arty-serin  210319B0C238

A NeTV2's name is a pure function of its DNA. Arty names are a hash chain resolved against a registry, so two serials never share a word and adding a board never renames an old one. Keep the registry as a JSON object of serial to name and pass it with --names registry.json to both name and labels.

Labels

rpi-hwid labels lays out 63.5 × 38.1 mm labels, 21 to an A4 sheet (the Avery L7160 grid), from a directory of collected documents. Print at 100 %. --outline draws the die-cut edges for an alignment print on plain paper; --start N skips N positions on the first sheet so a partly used sheet can be finished; --only rpi|fpga|usb limits the kinds; --list prints what would be generated and where.

$ rpi-hwid labels --data data/ --list
sheet 1 row 1 col 1  arty   arty-hawk
sheet 1 row 1 col 2  acorn  Acorn CLE-215+
sheet 1 row 1 col 3  rpi    Pi 3 Model B+ 1 GB 000000004fe3e7e4
sheet 1 row 2 col 1  rpi    Pi 4 Model B 2 GB 10000000ce8e3593
sheet 1 row 2 col 2  rpi    Pi 5 1 GB c36b093f773d46b8
sheet 1 row 2 col 3  rpi    Pi 5 4 GB d88100008543dc30
sheet 1 row 3 col 1  rpi    Pi Zero W 512 MB 000000005157f671
sheet 1 row 3 col 2  usb    ASIX AX88179A f8:e4:3b:0f:c1:e6
sheet 1 row 3 col 3  usb    ASIX Elec. Corp. AX88179 00:0e:c6:82:b5:e1
$ rpi-hwid labels --data data/ --out labels.pdf
9 labels on 1 sheet -> labels.pdf

Every label carries only what cannot change, and every identifier that might otherwise be typed is also a QR code. The three layouts, cropped from a rendered sheet:

Raspberry Pi. Model, memory and revision are decoded from the revision code, the serial runs up the left edge, the HAT band names what the probe found on the header (and the EEPROM UUID when there is one), and each soldered-down MAC gets its own QR. The layout is always the same, so a stack of them reads at a glance.

The Zero W's wired port comes from the bonnet, so its MAC is printed as the eth MAC. On a 3B+ or a Zero the wlan MAC follows from the eth MAC (the Broadcom-OUI rule: same serial digits, XOR 55:55:55), so it is printed even when the radio is off. On a Pi 4 or 5 it cannot be derived, so a disabled radio is stated as such.

FPGA boards. The maker and the derived name, the die, and the immutable identifier full width with a QR: Device DNA where read, the Digilent serial and flash part on an Arty, and a line to write the DNA on when it has not been read yet.

USB network adapters. The descriptors (USB version and speed, driver, VID:PID) and the MAC, full width with a QR, so a dongle can be matched to a DHCP lease from across the room.

The package ships only artwork it may: the public-domain USB trident. A --artwork DIR may add raspberry-pi.svg, alphamax.png, digilent.png and netv2.svg, which are trademarks of their owners (the Raspberry Pi logo is on the English Wikipedia file page; the Alphamax and Digilent marks are their GitHub organisation avatars). Without them a label sets the maker's name in type, as in the images above, which are regenerated from the test fixtures by docs/examples/render.py.

Using it from Python

Everything on the collecting side is a frozen dataclass (rpi_hwid.model); the probes emit JSON because they run on a Pi's Python 3.5.

from pathlib import Path

from rpi_hwid.collect import collect, load_collected
from rpi_hwid.names import netv2_name
from rpi_hwid.revision import decode_revision

collect(["rpi5-netv2", "pi@10.21.2.47"], Path("data"), jump="jump.example.org", fpga=True)

for host, doc in load_collected(Path("data")).items():
    s = doc.summary
    rev = decode_revision(s.revision)
    print(host, rev.model, rev.memory, s.power_class, [m.mac for m in s.macs])
    for board in s.fpga:
        name = netv2_name(board.dna) if board.kind == "netv2" and board.dna else ""
        print("  ", board.kind, board.identity, name)

Summary.from_dict refuses a field it does not know, so a probe that has grown a field is noticed when its document is loaded, not silently dropped. ProbeDocument.evidence keeps the whole raw document for anything the summary leaves out.

Development

uv sync --all-extras --group dev
uv run ruff check && uv run mypy && uv run pytest

The test suite renders a sheet from the fixture documents and decodes every QR on it with zxing (it needs pdftoppm from poppler and a monospace font). The two probe files must stay Python 3.5-clean: the tests refuse f-strings in them, and CI byte-compiles them with a real 3.5.

Releases are automatic: every green push to main publishes to PyPI. See RELEASING.md.

Origin

Worked out on a fleet of Pi Zero W, 3B+, 4 and 5 hosts carrying NeTV2, Acorn and Arty boards, powered by a mix of Waveshare PoE HATs and external PoE splitters, in September 2026. The rules above are what those boards showed; a board that behaves differently is a bug report.