sdss-almanac 0.2.12

Everything we've got

almanac

almanac scrapes headers from raw image files and cross-matches those against the SDSS database to create a comprehensive summary of everything ever observed with an APOGEE instrument.

Getting Started

Here are a few example cases of how almanac might be helpful:

List all exposures taken yesterday from either telescope:

almanac --mjd -1 -vv

Or just from Apache Point Observatory:

almanac --mjd -1 -vv --apo

Write out all exposures taken in the last month to january.h5:

almanac -o january.h5 --mjd-start -30

Write out all fiber observations during 2021, where we switched from plates to robotic fiber positioners:

almanac -vv --date-start 2021-01-01 --date-end 2021-31-12 --fibers

And it looks pretty, even when it warns you about missing exposures:

Installation

At Utah

If you want to use this at Utah, you can install it with:

module load almanac

[!TIP] We recommend you manage your own Python environment, but if you don't have one set up at Utah then you can use module load miniconda/3.8.5_astra.

Anywhere else

almanac needs local disk access to raw APOGEE data frames. If you are going to run it somewhere else, you should set up a Globus transfer of raw APOGEE frames, and ensure your internet address is whitelisted to remotely access the SDSS database.

We recommend using uv to manage Python environments. Using uv, you can install almanac with:

uv add sdss-almanac

Usage

Use almanac to see details on data taken today from both observatories, or specify the observatory:

almanac
almanac --apo # Apache Point Observatory
almanac --lco # Las Campanas Observatory

Specifying a date

If you want a particular day, either use the --mjd or --date (UTC) flags:

almanac --mjd 59300
almanac --date 2021-01-01

You can use negative MJD values to indicate days relative to today:

almanac --mjd -1 # Yesterday
almanac --mjd -7 # Last week

You can also specify a range of days:

almanac --mjd-start 59300 --mjd-end 59310 # Give me these 10 days
almanac --date-start 2021-01-01 --date-end 2021-01-31 # Give me all of January 2021

Fiber mappings

You can also use almanac to see the fiber mappings for a given plate (SDSS-IV) or FPS pointing (SDSS-V) by specifing the --fibers (or --fibres) flag. This will give you the mapping of fibers to targets, and the target properties.

almanac --mjd 60000 --fibres

The fiber mapping tables are cross-matched to the SDSS database to include the SDSS identifiers for each target. If you don't want to do this cross-match, you can use the --no-x-match flag. The --no-x-match flag is ignored if --fibers is not used.

Verbosity

By default there is minimal output to the terminal. You can adjust the verbosity level using -v:

• -v: show progress display only
• -vv: show progress display and exposure metadata

In verbose mode you can see exposure information in the terminal, and additional per-fiber metadata is stored in the HDF5 files that almanac creates.

Outputs

You can write the outputs to a structured HDF5 file by specifying an output path with the --output (or -O) flag. If the output path already exists, the default behaviour is to overwrite existing entries only. So if you run almanac once for MJD 60000 and output to a file, and then run it again for MJD 60001 and output to the same file, your file will have data for both MJDs.

almanac --output /path/to/file.h5 # Append today's data to existing file

An example structure of the HDF5 file is below:

apo/59300/exposures        # a data table of exposures
apo/59300/sequences        # a Nx2 array of exposure numbers (inclusive) that form a sequence
apo/59300/fibers/fps/1     # a data table of fiber mappings for FPS configuration id 1
apo/59300/fibers/plates/2  # a data table of fiber mappings for plate id 2

Configuration

You can view and change the almanac configuration settings through the almanac config interface. To view all current settings and to see the configuration file path:

almanac config show

To get a single configuration value

almanac config get logging_level

To set a configuration value

almanac config set logging_level 10