serialcables-atlas3 0.1.1

Python API for Serial Cables Atlas3 PCIe Gen6 Host Adapter Card

Serial Cables Atlas3 Python API

A Python library for controlling the Serial Cables Atlas3 PCIe Gen6 Host Adapter Card (PCI6-AD-x16HI-BG6-144).

Features

• Full Python API for all CLI commands
• Type-safe with dataclasses and enums
• Context manager support for automatic connection handling
• Command-line interface included
• Comprehensive error handling
• PyPI installable

Hardware

The Atlas3 Host Adapter Card features the Broadcom PEX90144 PCIe Gen6 Switch supporting:

• Up to 144 lanes and 72 ports
• Five 16-lane downstream stations
• PCIe Gen6 (64 GT/s) with FLIT mode
• Ultra low latency with FLIT & FEC
• Dynamic Port Reconfiguration (DPR)
• Hot-plug support

Connectors

Connector	Description	Ports
CN1	PCIe Straddle mount (x16)	Port 80
CN2	MCIO x8 (EXT upper)	Ports 120-127
CN3	MCIO x8 (EXT lower)	Ports 112-119
CN4	MCIO x8 (INT upper)	Ports 136-143
CN5	MCIO x8 (INT lower)	Ports 128-135
CN6	USB-C (SDB/SMART)	-
CN7	USB-C (MCU CLI)	-
CN9	12V 2x6 Power	-

Installation

pip install serialcables-atlas3

Or install from source:

git clone https://github.com/serialcables/serialcables-atlas3.git
cd serialcables-atlas3
pip install -e .

Quick Start

Python API

from serialcables_atlas3 import Atlas3

# Connect to the Atlas3 card
with Atlas3("/dev/ttyUSB0") as card:
    # Get version information
    info = card.get_version()
    print(f"Model: {info.model}")
    print(f"MCU Version: {info.mcu_version}")
    
    # Get host card status
    status = card.get_host_card_info()
    print(f"Temperature: {status.thermal.switch_temperature_celsius}°C")
    print(f"Power: {status.power.load_power}W")
    
    # Get port status
    ports = card.get_port_status()
    for port in ports.ext_mcio_ports:
        if port.is_linked:
            print(f"Port {port.port_number}: {port.negotiated_speed.value} x{port.negotiated_width}")
    
    # Run built-in self-test
    bist = card.run_bist()
    print(f"BIST: {'PASS' if bist.all_passed else 'FAIL'}")

Command-Line Interface

# Show version information
atlas3-cli -p /dev/ttyUSB0 version

# Show host card status
atlas3-cli -p /dev/ttyUSB0 status

# Show port status
atlas3-cli -p /dev/ttyUSB0 ports

# Run BIST
atlas3-cli -p /dev/ttyUSB0 bist

# Set clock spread
atlas3-cli -p /dev/ttyUSB0 spread 1  # 2500PPM

# Reset a connector
atlas3-cli -p /dev/ttyUSB0 reset 0

# Output as JSON
atlas3-cli -p /dev/ttyUSB0 --json status

API Reference

Connection

from serialcables_atlas3 import Atlas3

# Manual connection management
card = Atlas3("/dev/ttyUSB0", auto_connect=False)
card.connect()
# ... use the card ...
card.disconnect()

# Context manager (recommended)
with Atlas3("/dev/ttyUSB0") as card:
    # ... use the card ...
    pass  # Automatically disconnects

# Find available devices
devices = Atlas3.find_devices()
print(devices)  # ['/dev/ttyUSB0', '/dev/ttyUSB1']

System Information

# Get version info (ver command)
info = card.get_version()
print(info.company)       # "Serial Cables"
print(info.model)         # "PCI6-AD-x16HI-BG6-144"
print(info.mcu_version)   # "0.2.3"
print(info.sbr_version)   # "0032A022"

# Get host card info (lsd command)
status = card.get_host_card_info()
print(status.thermal.switch_temperature_celsius)  # 46.0
print(status.fan.switch_fan_rpm)                  # 6456
print(status.voltages.voltage_1v5)                # 1.499
print(status.power.load_power)                    # 126.251

# Get complete system info (sysinfo command)
sysinfo = card.get_system_info()

Port Status

# Get port status (showport command)
ports = card.get_port_status()
print(ports.chip_version)  # "A0"

for port in ports.ext_mcio_ports:
    print(f"Port {port.port_number}:")
    print(f"  Station: {port.station}")
    print(f"  Status: {port.status.value}")  # "Active", "Degraded", or "Idle"
    if port.is_linked:
        print(f"  Speed: {port.negotiated_speed.value}")  # "Gen6"
        print(f"  Width: x{port.negotiated_width}")
    print(f"  Max: {port.max_speed.value} x{port.max_width}")

# Check for degraded links
degraded = [p for p in ports.ext_mcio_ports if p.is_degraded]

Error Counters

# Get error counters (counters command)
counters = card.get_error_counters()
print(f"Total errors: {counters.total_errors}")

for c in counters.counters:
    if c.has_errors:
        print(f"Port {c.port_number}:")
        print(f"  Bad TLP: {c.bad_tlp}")
        print(f"  Bad DLLP: {c.bad_dllp}")
        print(f"  Flit Error: {c.flit_error}")

# Clear error counters
card.clear_error_counters()

Diagnostics

# Run BIST (bist command)
result = card.run_bist()
print(f"All passed: {result.all_passed}")

for device in result.devices:
    print(f"{device.channel} {device.device_name}: {device.status}")

Configuration

from serialcables_atlas3 import OperationMode, SpreadMode

# Mode configuration (setmode/showmode commands)
current_mode = card.get_mode()
print(f"Current mode: {current_mode.value}")  # 1, 2, 3, or 4

card.set_mode(OperationMode.MODE_1)  # Common clock, precoding enabled
# Note: Requires controller reset to take effect

# Clock spread (spread command)
spread = card.get_spread_status()
print(f"Spread enabled: {spread.enabled}")

card.set_spread(SpreadMode.DOWN_2500PPM)  # -0.25% spread
card.set_spread("off")  # Disable spread

# Clock output (clk command)
clk = card.get_clock_status()
print(f"Straddle clock: {'enabled' if clk.straddle_enabled else 'disabled'}")

card.set_clock_output(True)   # Enable clock output
card.set_clock_output(False)  # Disable clock output

# Flit mode (flit command)
flit = card.get_flit_status()
print(f"Station 2 flit disable: {flit.station2}")

card.set_flit_mode("all", False)  # Enable flit on all stations
card.set_flit_mode(2, True)       # Disable flit on station 2

# SDB routing (sdb command)
card.set_sdb_target("usb")  # Route to USB for SwitchCLID/ARCTIC
card.set_sdb_target("mcu")  # Route to MCU for normal operation

Reset Commands

# Reset connector (conrst command)
card.reset_connector(0)      # Reset CON0 (EXT MCIO upper)
card.reset_connector("all")  # Reset all connectors

# Reset MCU (reset command)
card.reset_mcu()

Register Access

# Read registers (dr command)
dump = card.read_register(0x60800000, count=16)
for addr, value in sorted(dump.values.items()):
    print(f"0x{addr:08X}: 0x{value:08X}")

# Write register (mw command)
card.write_register(0xFFF0017C, 0xFFFFFFFF)

# Read port registers (dp command)
port_dump = card.read_port_registers(32)  # Golden finger port

# Read flash (df command)
flash = card.read_flash(0x400, count=16)

I2C Access

# Read from I2C device (iicwr command)
result = card.i2c_read(
    address=0xD4,
    connector=2,
    channel="a",
    read_bytes=8,
    register=0
)
print([hex(b) for b in result.data])

# Write to I2C device (iicw command)
card.i2c_write(
    address=0xD4,
    connector=2,
    channel="a",
    data=[0xFF]
)

Connector and Port Mapping

Station	Connector	Ports	Description
STN2	-	32	Golden Finger (Upstream)
STN5	CON4	80	PCIe Straddle
STN7	CON0	112-118	EXT MCIO upper
STN7	CON1	120-126	EXT MCIO lower
STN8	CON2	128-134	INT MCIO upper
STN8	CON3	136-142	INT MCIO lower

LED Indicators

Status LEDs

LED	Color	Description
SLED1	Red	System error
SLED2	Green	Heartbeat (blinking = managed FW running)
SLED3	Green	MCU status (blinking = MCU running)

Link Speed LEDs (Blue)

Blink Rate	Speed
0.25 Hz	Gen1 (2.5 GT/s)
0.5 Hz	Gen2 (5.0 GT/s)
1.0 Hz	Gen3 (8.0 GT/s)
2.0 Hz	Gen4 (16.0 GT/s)
4.0 Hz	Gen5 (32.0 GT/s)
Always on	Gen6 (64.0 GT/s)

Error Handling

from serialcables_atlas3 import (
    Atlas3,
    Atlas3Error,
    ConnectionError,
    CommandError,
    TimeoutError,
    InvalidParameterError,
)

try:
    with Atlas3("/dev/ttyUSB0") as card:
        card.set_mode(5)  # Invalid mode
except InvalidParameterError as e:
    print(f"Invalid parameter: {e}")
except ConnectionError as e:
    print(f"Connection failed: {e}")
except TimeoutError as e:
    print(f"Command timed out: {e}")
except CommandError as e:
    print(f"Command failed: {e}")
except Atlas3Error as e:
    print(f"Atlas3 error: {e}")

Development

# Clone the repository
git clone https://github.com/serialcables/serialcables-atlas3.git
cd serialcables-atlas3

# Install in development mode with dev dependencies
pip install -e ".[dev]"

# Run tests
pytest

# Format code
black src tests
isort src tests

# Type checking
mypy src

# Lint
ruff check src tests

License

MIT License - see LICENSE for details.

Support

• Website: https://serialcables.com
• Email: [e-mail]
• Address: 8811 American Way, Suite 110, Englewood, CO 80107

Related Products

• PCI6-AD-x16HI-BG6-144: Gen6 x16 – 4, x8 MCIO Host Card w/ 1x16 Straddle Mount Connector (A0 144-lane Switch)8-bay E3 passive JBOF