usb-rea — Reverse Engineer any USB gadget

_{If you find this useful, you can support me by getting a SkinToScan pack, my other project. It's a one-time purchase that directly funds my open-source work.}

Got a USB device that only ships a Windows vendor app (case LCD, RGB controller, mouse, "smart" lamp)? Click around in the vendor app while usb-rea captures the USB traffic (usbmon on Linux, USBPcap on Windows), diffs the packets per action, infers the protocol, and writes an open-source Python/libusb driver — with every conclusion linked to the exact packets that prove it.

Status: alpha (v0.5.0, on PyPI). Validated on synthetic devices, on protocols documented by liquidctl and rivalcfg, and on public Wireshark captures — see docs/VALIDATION.md. Not yet tested on a physical gadget: your captures are welcome.

Try it in 10 seconds (no hardware needed)

pip install usb-rea
usb-rea demo --device fan

fan    100%  0x5a | counter (+1 per message) | 0x10 | u16be round(value * 1 + 0) | 0x00 | u16le crc16_modbus(bytes[0:6])
color  100%  0x5a | counter (+1 per message) | 0x20 | round(value * 1 + 0) | round(value[1] * 1 + 0) | round(value[2] * 1 + 0) | u16le crc16_modbus(bytes[0:6])
mode   100%  0x5a | counter (+1 per message) | 0x30 | lookup 1→0x11, 2→0x22, 3→0x47 | 0x00 | 0x00 | u16le crc16_modbus(bytes[0:6])

device replies:
fan    6/6  0xa5 | = query byte 2 (0x10) | = query byte 1 | u16le round(value * 1 + 0) | sum8(bytes[0:5])
poll 1 7/7  0xa5 | = query byte 2 (0x40) | u16le rpm = raw, seen 794..4012 | u8 temp = raw, seen 35..38 | 0x00 | sum8(bytes[0:6])

12 of 12 'seen' observations matched a reply byte (rpm, temp)

It writes a synthetic capture of a fan controller (its vendor app also polls the fan's status, and the markers note what the app's screen showed, seen rpm 1207 temp 37), recovers the protocol and the replies, names the readings, and writes report.md (every claim linked to Wireshark frame numbers) and a working pyusb driver that encodes values it never saw and decodes what the fan answers.

--device lamp (default) is a simple 8-bit device; --device dial shows 32-bit values and packed bitfields:

position     100%  0xa5 | 0x01 | u32le round(value * 1 + 0) | sum8(bytes[0:6])
level        100%  0xa5 | 0x02 | bits[0:4] = round(value * 1 + 0) | 0x00 | sum8(bytes[0:4])

What it can infer

Linear fits must survive leave-one-out cross-checks; otherwise usb-rea falls back to an honest lookup table and says so.

Real device workflow (Linux)

sudo modprobe usbmon
usb-rea capture start -o lamp.pcapng
usb-rea mark -m lamp.pcapng.actions.json "brightness 0%"    # then click it in the vendor app
usb-rea mark -m lamp.pcapng.actions.json "brightness 50%"   # ...repeat for 3+ values per setting
usb-rea capture stop
usb-rea report lamp.pcapng -o report.md
usb-rea scaffold lamp.pcapng -o lamp_driver.py
usb-rea dissector lamp.pcapng -o lamp.lua      # Wireshark dissector for the same protocol

Captured on Windows with USBPcap/Wireshark and no markers? Click each action with a short pause in between, then just list them in order — usb-rea splits the traffic at the pauses:

usb-rea report lamp.pcapng --labels "brightness 0%; brightness 50%; brightness 100%; power off; power on"
usb-rea scaffold lamp.pcapng --labels labels.txt -o lamp_driver.py   # one label per line

(Markers, if you have them, are a JSON list of {"label", "start", "end"} epoch timestamps.)

Most vendor apps also poll the device on their own (a "get status" every few hundred ms, keep-alives). usb-rea spots identical host→device messages sent on a steady rhythm, away from your clicks, and sets them aside before splitting and diffing; the report lists them under Background traffic (ignored) with their period and frame numbers. A constant "apply" packet that always follows a real command is not treated as background. Polls that carry a sequence number are caught too: same-shape messages that differ only in a byte counting up by one (plus a trailing checksum that changes with it) show up as e.g. aa 10 ?? 00 ??. Those need at least 8 copies, so a user stepping a value by one is not mistaken for a poll.

Device responses

Devices answer too: an ACK after each command, a status reply to every poll (RPM, temperature, firmware version), or the data of a GET_REPORT. usb-rea pairs each query with the IN transfer that follows it (by endpoint and typical delay, so a poll sent in the middle of a click doesn't steal the click's reply) and decodes the replies with the same machinery: constants, bytes that echo the query (command id, sequence number), counters, checksums, and values fitted to your labels (fan 1200 → u16le in the reply). Anything else that varies is reported as a reading with its observed range, and the report says that its meaning is unknown. A 16-bit reading is only claimed when one byte order changes smoothly and the other jumps. The generated driver gets query_<name>() methods that send the query, read the reply and return a dict ({"reading_2": 1834, "checksum_ok": True, …}). Try it with usb-rea demo --device fan or on a capture with polls.

Naming readings: tell it what the vendor app shows

A reading is just bytes until you say what it is. While capturing, note what the vendor app displays now and then:

usb-rea mark -m fan.pcapng.actions.json "seen rpm 1180 temp 34"   # several name/value pairs are fine

A seen marker is an observation, not an action: it does not end the action in progress, is never diffed, and never becomes a command. Each observation is compared with the reply just before it (what the app was showing) or just after it, within 1 s. A reading takes the name when it equals every observation of that name (2+ observations, within one unit or 1%), or when a linear raw = value * scale + bias fits them exactly and survives the same leave-one-out check as commands (3+ observations with distinct values). Two neighbouring byte readings are also tried as one 16-bit LE/BE number. The report shows the formula with the frames and marker times behind it, and lists observations that matched nothing; the driver returns {"rpm": 1180, "temp": 34, "ok": True, …}.

On/off states work too: mark "seen pump on, alarm off" (also true/false, yes/no). A name seen both on and off becomes a status flag, the one bit of a reply byte that is 1 every time the app said on and 0 every time it said off; several flags can share a byte, and the driver returns {"pump": True, "alarm": False, …}. Two bits that always flip together are left unnamed, and bits of a flag byte that change but were never named are pointed out in the report. Limits: only replies (not commands) are named, a name that fits two places is left out, 32-bit and multi-bit packed readings are not tried, and display rounding coarser than one unit (e.g. RPM shown in steps of 10) only works for the identity, not for a scaled fit. seen labels in --labels mode have no timestamp and are skipped.

MCP server

pip install usb-rea then add usb-rea mcp as a stdio server. Tools: capture_start, capture_stop, mark_action, diff_actions, report, scaffold_driver, hid_descriptor (decode a HID report descriptor / report payloads), wireshark_dissector, replay_packet (refuses unless the human confirmed). Analysis tools accept the same labels argument as the CLI for marker-free captures.

With uv no install step is needed:

{"mcpServers": {"usb-rea": {"command": "uvx", "args": ["--from", "usb-rea", "usb-rea", "mcp"]}}}

For Claude Code: claude mcp add usb-rea -- uvx --from usb-rea usb-rea mcp. The server is also listed on the official MCP Registry as io.github.emirmrkaljevic/usb-rea and on Glama, which builds it from the repo's Dockerfile and checks that it starts and lists its tools.

How it works

1. usb-rea capture start — record traffic (usbmon / USBPcap)
2. usb-rea mark "brightness 50%" — label each action you take in the vendor app (mark "seen rpm 1180" notes what it displays)
3. usb-rea diff — which bytes change per action, value correlation, checksums, counters
4. usb-rea infer — message templates + evidence report
5. usb-rea scaffold — generate a pyusb driver and replay tests
6. usb-rea dissector — write a Wireshark Lua dissector for the inferred protocol
7. usb-rea replay — send packets to the device (only with explicit confirmation)
8. usb-rea hid — decode a HID report descriptor from a capture (GET_DESCRIPTOR 0x22) or from hex, and decode report payloads
9. usb-rea mcp — the same tools as an MCP server for AI agents

Wireshark dissector

usb-rea dissector capture.pcapng -o lamp.lua turns the inferred protocol into a Wireshark Lua plugin, so you can keep capturing and read the traffic as commands instead of hex:

wireshark -X lua_script:lamp.lua capture.pcapng
tshark -X lua_script:lamp.lua -r capture.pcapng -Y 'usbrea.command == "brightness"'

Each matching packet gets a usbrea tree with the command name, decoded values (usbrea.brightness.value), counters, lookup labels, and a checksum check (usbrea.checksum_ok, with an expert warning on mismatch); the Info column reads brightness 50. It works for bulk, interrupt and control/HID SET_REPORT transfers, from usbmon or USBPcap, and needs no bit library (Wireshark 3.x and 4.x). -n NAME changes the filter prefix. CI runs every generated dissector through tshark.

HID devices

Most RGB keyboards, mice, headsets and LCD gadgets are HID with a vendor-defined page. If the capture includes the report descriptor (start capturing, then replug the device), the report gets a section with every report's ID, size and fields, and each inferred command is tagged with the HID report it travels in. Without a capture:

usb-rea hid /sys/class/hidraw/hidraw0/device/report_descriptor --items
usb-rea hid capture.pcapng --decode "10ff0d1d000000" --type Output

Roadmap

• pcap/pcapng parser (usbmon + USBPcap)
• action markers and per-action diffing
• checksum detection (sum8, xor8, neg/inv sum8, CRC8, CRC16 variants)
• evidence-backed protocol report
• driver scaffolding (pyusb, bulk/interrupt + control/HID SET_REPORT)
• confirmed replay
• MCP server
• rolling counters, multi-byte (16/32-bit LE/BE) values, lookup tables, multi-value actions
• packed bitfields
• validation against documented protocols (liquidctl, rivalcfg)
• HID report descriptor decoding (usb-rea hid), with captured commands mapped to their HID reports
• emulated-device CI (dummy_hcd + configfs HID; script in scripts/gadget_e2e.sh)
• real-hardware case studies
• multi-packet transactions (write + apply), including checksums over earlier packets
• background traffic: periodic status polls / keep-alives are detected and ignored
• device responses: replies to commands, background polls and GET_REPORT decoded, query_*() driver methods
• named readings: seen rpm 1180 markers name and scale reply readings (identity or linear, 8/16-bit)
• on/off status flags: seen pump on / seen pump off name single bits of reply bytes
• state machines (multi-step handshakes)

Legal

Reverse engineering for interoperability is permitted (EU Directive 2009/24/EC Art. 6, US DMCA §1201(f)). usb-rea only analyzes traffic of devices you own and never redistributes vendor code.

License

MIT