wattpilot-api 1.0.0

Async Python library to connect to a Fronius Wattpilot Wallbox

wattpilot-api

Async Python library for Fronius Wattpilot Wallbox devices.

Connects to Wattpilot EV chargers over WebSocket using a reverse-engineered API (the same protocol used by the official Wattpilot.Solar mobile app). Provides real-time property synchronization, an MQTT bridge, Home Assistant discovery, and an interactive CLI shell.

Features

• Fully async — built on asyncio and websockets, compatible with Home Assistant
• All Wattpilot hardware — supports standard (V2) and Flex models via PBKDF2 and bcrypt authentication
• 388+ properties — access every charger property in real time
• MQTT bridge — publish properties and subscribe to commands via aiomqtt
• Home Assistant discovery — automatic entity creation with proper device classes
• Interactive shell — async CLI with TAB completion via prompt_toolkit
• Type-safe — full type hints, mypy --strict, PEP 561 py.typed marker
• 100% test coverage — 241 unit tests + 18 integration tests

Requirements

• Python 3.12+
• Local network access to a Fronius Wattpilot charger

Installation

pip install wattpilot-api

For development:

pip install -e ".[dev]"

Quick Start

As a library

import asyncio
from wattpilot_api import Wattpilot, LoadMode

async def main():
    async with Wattpilot("192.168.1.100", "your_password") as wp:
        # Read properties
        print(f"Serial: {wp.serial}")
        print(f"Firmware: {wp.firmware}")
        print(f"Power: {wp.power:.2f} kW")
        print(f"Amperage: {wp.amp} A")
        print(f"Car connected: {wp.car_connected}")
        print(f"Mode: {LoadMode(wp.mode).name}")

        # Set charging amperage
        await wp.set_power(16)

        # Set charging mode
        await wp.set_mode(LoadMode.ECO)

        # Register a callback for property changes
        def on_change(name, value):
            print(f"{name} = {value}")

        unsub = wp.on_property_change(on_change)

        # Access all 388+ raw properties
        for key, value in sorted(wp.all_properties.items()):
            print(f"  {key} = {value}")

        unsub()  # unsubscribe when done

asyncio.run(main())

Interactive shell

export WATTPILOT_HOST=192.168.1.100
export WATTPILOT_PASSWORD=your_password
wattpilotshell

With MQTT and Home Assistant

export WATTPILOT_HOST=192.168.1.100
export WATTPILOT_PASSWORD=your_password
export MQTT_ENABLED=true
export MQTT_HOST=your_mqtt_broker
export HA_ENABLED=true
wattpilotshell

Supported Hardware

Device	Auth	Status
Wattpilot Home (V2)	PBKDF2	Tested
Wattpilot Home FLEX 11 C6	bcrypt	Supported
Wattpilot Home FLEX 22kW	bcrypt	Supported
Wattpilot (cloud via Fronius API)	PBKDF2	Supported

Authentication is auto-detected:

1. If the authRequired message includes a hash field, that algorithm is used
2. Otherwise, if devicetype is wattpilot_flex, bcrypt is used
3. Otherwise, PBKDF2 is used (default)

API Reference

Wattpilot Client

from wattpilot_api import Wattpilot

# Constructor
wp = Wattpilot(
    host="192.168.1.100",
    password="your_password",
    serial=None,           # auto-detected from device
    cloud=False,           # True for Fronius cloud connection
    connect_timeout=30.0,  # seconds
    init_timeout=30.0,     # seconds
)

# Connect / disconnect
await wp.connect()
await wp.disconnect()

# Or use as async context manager
async with Wattpilot("192.168.1.100", "password") as wp:
    ...

Properties

Property	Type	Description
wp.connected	bool	Connection status
wp.serial	str	Device serial number
wp.name	str	Device name
wp.manufacturer	str	Manufacturer ("fronius")
wp.device_type	str	Device type ("wattpilot_V2", "wattpilot_flex")
wp.version	str	Firmware version
wp.amp	int	Current amperage setting
wp.mode	int	Charging mode (3=Default, 4=Eco, 5=NextTrip)
wp.car_connected	int	Car status (1=No car, 2=Charging, 3=Ready, 4=Complete)
wp.allow_charging	bool	Whether charging is allowed
wp.voltage1/2/3	float	Phase voltages
wp.amps1/2/3	float	Phase currents
wp.power1/2/3	float	Phase power (kW)
wp.power	float	Total power (kW)
wp.frequency	float	Grid frequency (Hz)
wp.energy_counter_since_start	float	Session energy (Wh)
wp.energy_counter_total	float	Lifetime energy (Wh)
wp.error_state	int	Error code
wp.cable_type	int	Cable capacity (A)
wp.cable_lock	int	Lock mode
wp.access_state	int	Access state
wp.phases	list	Phase configuration
wp.all_properties	dict	All 388+ raw properties

Commands

await wp.set_power(16)                    # Set amperage (6-32)
await wp.set_mode(LoadMode.ECO)           # Set charging mode
await wp.set_property("fna", "MyCharger") # Set any writable property

Callbacks

# Sync or async callbacks supported
unsub = wp.on_property_change(lambda name, value: print(f"{name}={value}"))
unsub()  # unsubscribe

unsub = wp.on_message(lambda msg: print(msg["type"]))
unsub()

Enums

from wattpilot_api import LoadMode, CarStatus, ErrorState, AccessState, CableLockMode

LoadMode(wp.mode)           # LoadMode.DEFAULT / ECO / NEXTTRIP
CarStatus(wp.car_connected) # CarStatus.NO_CAR / CHARGING / READY / COMPLETE

Exceptions

from wattpilot_api import WattpilotError, AuthenticationError, ConnectionError

try:
    await wp.connect()
except AuthenticationError:
    print("Wrong password")
except ConnectionError:
    print("Cannot reach device")

MQTT Bridge

The MqttBridge class publishes property changes to MQTT and subscribes to set commands.

from wattpilot_api import Wattpilot, MqttBridge, MqttConfig
from wattpilot_api.definition import load_api_definition

api_def = load_api_definition()
config = MqttConfig(host="localhost", port=1883)

async with Wattpilot("192.168.1.100", "password") as wp:
    bridge = MqttBridge(wp, config, api_def)
    await bridge.start()
    # ... bridge publishes property changes to MQTT
    await bridge.stop()

Home Assistant Discovery

from wattpilot_api import HomeAssistantDiscovery, HaConfig

ha = HomeAssistantDiscovery(wp, bridge, HaConfig(enabled=True), api_def)
await ha.discover_all()
await ha.publish_initial_values()

Development

# Install with dev dependencies
pip install -e ".[dev]"

# Run tests (100% coverage required)
pytest --cov=wattpilot_api --cov-report=term-missing --cov-fail-under=100

# Run integration tests against a real device
WATTPILOT_HOST=192.168.1.100 WATTPILOT_PASSWORD=password pytest -m integration -v

# Lint and type check
ruff check src/ tests/
mypy src/wattpilot_api/

# Pre-commit (runs ruff, ruff-format, mypy)
pre-commit run --all-files

Project Structure

src/wattpilot_api/
├── __init__.py          # Public API exports
├── client.py            # Async WebSocket client
├── auth.py              # PBKDF2 + bcrypt authentication
├── models.py            # Enums and dataclasses
├── exceptions.py        # Exception hierarchy
├── definition.py        # YAML property metadata loader
├── mqtt.py              # Async MQTT bridge
├── discovery.py         # Home Assistant MQTT discovery
├── shell.py             # Async CLI shell
├── py.typed             # PEP 561 marker
└── resources/
    └── wattpilot.yaml   # Property definitions (3300+ lines)

API Sources

The WebSocket API has been reverse-engineered from multiple sources:

• go-eCharger API v1
• go-eCharger API v2

Changelog

See CHANGELOG.md for version history, migration guide, and upstream issue fixes.

License

MIT License — see LICENSE for details.

Disclaimer

This project uses a reverse-engineered API and is not officially supported by Fronius. Use at your own risk.