xtalx 1.3.8

Drivers and tools for the XtalX sensor family.

xtalx

This package provides a library for interfacing with the XtalX pressure and density/viscosity sensors. Python version 3 is required. The easiest way to install the xtalx module is using pip:

python3 -m pip install xtalx

Note that you may wish to use sudo to install xtalx for all users on your system:

sudo python3 -m pip install xtalx

You may also install the package from the source using:

make install

or:

sudo make install

xtalx_p_discover

The xtalx package includes the xtalx_p_discover binary which can be used to list all XtalX pressure sensors that are attached to the system and their corresponding firmware versions:

~$ xtalx_p_discover
******************
Sensor SN: XTI-7-1000035
 git SHA1: 61be0469c1162b755d02fd9156a2754bebf24f59.dirty
   Version: 0x0107

xtalx_p_test

The xtalx package includes a simple test binary that will connect to an XtalX pressure sensor and continuously print the current pressure and temperature reading:

~$ xtalx_p_test
XtalX(XTI-7-1000035): 23.973375 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.973375 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.973375 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.963872 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.963872 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.954370 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.954370 PSI, 23.947930 C
XtalX(XTI-7-1000035): 23.973375 PSI, 23.947930 C
...

Terminate the program by pressing Ctrl-C.

xtalx_z_discover

The xtalx packages includes the xtalx_z_discover binary which can be used to list all XtalX density/viscosity sensors that are attached to the system and their corresponding firmware version:

~% xtalx_z_discover
******************
  Product: XtalX TCSC
Sensor SN: TCSC-1-2000045
 git SHA1: b50b8e4a406f0b8585f50c1f9aa7c95145d4810d
  Version: 0x0101

xtalx_z_get_info

The xtalx package includes the xtalx_z_get_info binary that can be used to get a bit more detailed information about a sensor:

~% xtalx_z_get_info
[1691531122175214000] I: Controlling sensor TCSC-1-2000045 with firmware 0x101 (b50b8e4a406f0b8585f50c1f9aa7c95145d4810d).
*************************************
     Serial Num: TCSC-1-2000045
       Git SHA1: b50b8e4a406f0b8585f50c1f9aa7c95145d4810d
     FW Version: 0x0101
           HCLK: 80000000
           DCLK: 2500000
           ACLK: 1250000
            HSE: 10 MHz
    Max cmd len: 16384
       # resets: 1
     Drive Type: DriveType.INTERNAL_DRIVE
   Reset Reason: ResetReason.POWER_ON_RESET
      Reset CSR: 0x0C004400
      Reset SR1: 0x00000000
Max sweep freqs: 1024
-----------------------
Electrical calibration:
 Calibration Date: 1683682186 (Tue May  9 19:29:46 2023)
         R Source: 10037.000000
       R Feedback: 149850.000000
         DAC-to-V: 2.208075 + -0.000256*x
         ADC-to-V: 1.674066 + 0.000204*x
     Nominal VDDA: 3.35
-----------------------
Tuning fork calibration:
 Calibration Date: 1683682197 (Tue May  9 19:29:57 2023)
Cal DAC Amplitude: 975 (0.25V)

xtalx_z_gl_track_mode

The xtalx package includes the xtalx_z_gl_track_mode binary that is the core tool for use with the density/viscosity sensor. It features a GUI instead of command-line output. To execute it:

~% xtalx_z_gl_track_mode

xtalx_z_cli_track_mode

The xtalx package includes the xtalx_z_cli_track_mode binary that is similar to the GUI track mode tool but only prints log messages to the console and write measurements to the .csv files. This allows it to be run on a headless system. To execute it:

~% xtalx_z_cli_track_mode

Windows use

On Windows, the binaries are all launched via the command line just like on Linux and macOS, however Windows can’t automatically find them. In order to launch them, you need to execute them using their full Python path as follows:

python3 -m xtalx.tools.p_sensor.discover
python3 -m xtalx.tools.p_sensor.xtalx_test_yield
python3 -m xtalx.tools.z_sensor.discover
python3 -m xtalx.tools.z_sensor.get_info
python3 -m xtalx.tools.z_sensor.gl_track_mode

On Windows, it is also common to have the Python interpreter installed under the name “py” or “py3”, so if “python3” does not work for you it is recommended to try one of the shorter command names. If the Python interpreter cannot be found, it may not be installed at all so should be installed via the Microsoft Store (it is a free, open-source install).