yarbo-local

Local-first tooling and, later, the asyncio library behind a Home Assistant integration for Yarbo robots. It talks to the anonymous MQTT broker the robot runs on your LAN and to nothing else. No Yarbo account, no vendor servers, no telemetry.

Status: pre-alpha. Phase 0 validated the protocol on real hardware (firmware 3.14.11) and produced the knowledge base in protocol/: 23 commands verified with captures, the rest marked as candidates that cannot be sent. The library core is in place: a registry-gated session, typed state, the map, plan control (start, pause, resume, stop, return to dock, each verified against the robot), a fixture-driven simulator and a small client. It is on PyPI as yarbo-local. The Home Assistant integration (yarbo-local-ha) shows and controls the robot, and carries its own map card, which draws the map, the robot and plan progress.

What is here

Quick start

git clone https://github.com/yarbo-local/yarbo-local
cd yarbo-local
uv sync --extra dev
uv run yarbo-local discover 192.168.40.0/24
uv run yarbo-local sniff 192.168.40.23 --out captures/idle.jsonl
uv run yarbo-local dump captures/idle.jsonl --keys --app
uv run yarbo-local probe 192.168.40.23 get_device_msg

probe only sends commands on a short allowlist of reads plus the wake-up command. It will not send anything that moves the robot, changes the map, or touches settings.

Using the library

import asyncio
from yarbo_local import YarboRobot


async def main() -> None:
    async with YarboRobot.for_host("192.168.50.184") as robot:
        state = await robot.snapshot()
        print(state.activity, state.battery, state.head_name)
        for plan in await robot.plans():
            print(plan.id, plan.name)
        robot.on_state(lambda s: print("changed:", s.activity))
        await asyncio.sleep(30)


asyncio.run(main())

Rules the session enforces, on purpose:

• Only commands in protocol/commands.yaml can be sent. Names in its forbidden section are not entries and can never be sent, with or without flags.
• A command whose status is candidate is refused unless the session was opened with allow_candidates=True. The Home Assistant integration never does that; the Studio does.
• A command with risk: confirm needs confirmed=True on the call.
• The wake command and the controller role are used only when the command's flags say they are needed, and the controller is itself still a candidate.
• Outbound encoding follows the robot's firmware, or what it has been seen sending, so a robot on 3.9 or later never silently drops a plaintext command.
• The connection loop never returns on a dropped broker; it backs off with jitter and reconnects.

The same CLI can show what the library sees, stand up a fake robot from a fixture for development without hardware, and open the Studio, a local web UI for watching the protocol, documenting fields and saving fixtures (see docs/studio.md):

uv run yarbo-local status yarbo.localdomain --watch 30
uv run yarbo-local sim protocol/fixtures/3.14.11/get_device_msg-asleep.jsonl --broker 127.0.0.1
uv run yarbo-local studio yarbo.localdomain

Can't see the base station in your router or controller?

You won't. The base station bridges the rover's HaLow link onto your LAN behind a locally administered MAC that never associates with an access point or asks your DHCP server for an address. It picks a static address for itself, inside your DHCP pool, and it has no management page. Network controllers such as UniFi list clients by association or wired port, so the base station simply does not exist to them, even while it answers on ports 1883, 8883 and 22.

Do not spend an afternoon on this. Scan the subnet instead:

uv run yarbo-local discover 192.168.1.0/24 --wait 8

Every host carrying Yarbo traffic is listed with the serial it carries and its DNS name, if it has one. A robot is identified by its own topics and nothing else; the tool reads no ARP table and runs no other program. The rover and the base station both answer, with the same data. Then protect yourself from the address collision Yarbo set up for you: either shrink your DHCP pool so it starts above the base station's address, or put the Yarbo Wi-Fi association on an isolated VLAN so the whole bridge moves out of your main network.

Safety and privacy

The robot's broker has no authentication. Anyone on its network segment can drive it. Put the robot on its own VLAN, allow only the machine running this tooling (and later Home Assistant) to reach port 1883, and think deliberately about whether the robot should have internet access at all. Captures contain your serial number, coordinates and network details; use --redact and review the file before sharing it.

Have more than one robot?

Nobody on the project does. One command tells us what we cannot find out ourselves, without sharing a serial, an address or a position: see docs/multi-robot.md.

Contributing protocol knowledge

Read protocol/README.md. A command becomes verified only with a fixture showing the request and the reply on real hardware, with the firmware version recorded. Pull requests that add knowledge without evidence are asked for a capture.

Releasing

Releases are published to PyPI by GitHub Actions through trusted publishing, with a manual approval and no token anywhere. See docs/releasing.md.

License and trademark

MIT. Protocol facts were assembled from the vendor's MIT-licensed SDK, from python-yarbo, home-assistant-yarbo, the jtubb and briangann forks of the vendor integration, and the steves2j map editor; see protocol/commands.yaml for per-entry sources. Yarbo is a trademark of its owner. This project is not affiliated with, endorsed by, or supported by Yarbo.