CableProbe

CableProbe is an open-source defensive USB cable analysis tool for Linux (developed and tested on Raspberry Pi OS / Debian, and reasonably portable to other Debian/Ubuntu systems).

• Home page: https://www.cableprobe.com
• Source & downloads: https://github.com/rosscooney/CableProbe (releases)
• Package: cableprobe on PyPI

CableProbe watches a sacrificial Linux host while you connect an unknown USB cable — USB-C or USB-A, charge-only or data — then compares before, during and after to surface hidden HID devices, rogue network gadgets, mass storage, serial channels, transient enumeration and kernel errors.

CableProbe only observes, records and reports. It does not inject payloads, exploit anything, capture credentials, establish persistence or provide remote access. It is a monitoring tool for a sacrificial test host.

⚠️ CableProbe cannot prove that a cable is safe or uncompromised. A clean report means CableProbe did not observe anything notable during that session, not that the cable is benign. Use it as one input to your own judgement.

⚠️ Run this on a dedicated, disposable Raspberry Pi that holds no sensitive data and is isolated from networks you care about. Treat any cable under test as hostile hardware.

How it works

A session has three phases:

CableProbe then compares the three phases and writes a structured JSON report describing everything that appeared, disappeared or changed in correlation with the cable, and runs a set of YAML-configurable detection rules over those differences to produce prioritised findings. The console summary ends with a plain-language "What this means" box — an overall read of the session and what to do next, written for a moderately technical reader rather than a USB specialist.

Connector type does not matter — CableProbe watches how the host reacts, not the plug. Any cable you can get one end of into a port on the test Pi works: USB-C or USB-A, either orientation, with a passive adapter if you need one. The usbc_pd probe additionally reports Type-C power-delivery state when the Pi exposes a Type-C port, and simply skips otherwise.

Probes (observation only)

Probes that need hardware or kernel interfaces the host does not expose (no Type-C class, no /sys/bus/pci, …) are skipped automatically. cableprobe check lists them as FAIL with the reason, and a run notes them once as skipped: … (interface not present on this host) — that is expected, not an error. Raspberry Pi 4, for example, has no usbc_pd (its USB-C port is power-only); Raspberry Pi 5 does. To silence a skip entirely, drop the probe from probes.enabled in your config.

Two probes have side effects worth knowing about:

• keystroke_cadence reads /dev/input/event* for key-press timing only — the key code of every event is discarded before anything is stored, so it never learns which keys were pressed. Set capture_keystroke_timing: false to disable it.
• wifi_scan (opt-in) runs an active Wi-Fi scan (iw / nmcli) at each phase boundary, which briefly interrupts any Wi-Fi association on that interface. It never associates with a discovered AP. With it enabled, the one rule that fires is a strong AP that appeared on connect and disappeared again on disconnect — a fixed AP on your premises never trips it.

Install

Requires Python 3.11+. See DISTRIBUTING.md for the full picture; the short version:

# 1. pip / pipx on an existing Raspberry Pi OS / Debian host
pipx install cableprobe
sudo apt install usbutils util-linux iw     # CLI tools CableProbe shells out to
#   note: this puts `cableprobe` in ~/.local/bin, which is NOT on root's PATH.
#   run `cableprobe link` once (it escalates itself) so `sudo cableprobe` works
#   (see "command not found" under Usage).

# 2. one command on a Pi (isolated venv under /opt/cableprobe) — RECOMMENDED for
#    a test rig: links /usr/local/bin/cableprobe so `sudo cableprobe` just works,
#    and apt-installs the helper CLIs (usbutils, util-linux, iw, pciutils)
sudo ./scripts/install.sh                    # sudo scripts/uninstall.sh to remove

# 3. from a checkout, for development
git clone https://github.com/rosscooney/CableProbe cableprobe && cd cableprobe
python3 -m venv .venv && . .venv/bin/activate
pip install -e ".[dev]"

For a disposable Raspberry Pi image, build your own from stock Raspberry Pi OS using the pi-gen custom stage in packaging/pi-gen/ — CableProbe ships the recipe, not a prebuilt image.

pyudev needs libudev (present on Raspberry Pi OS / Debian). On non-Linux hosts CableProbe still installs and its --help / check / report commands work, but the live probes are unavailable.

Upgrading

cableprobe upgrade            # checks PyPI directly, then upgrades this install
cableprobe upgrade --check    # just report whether a newer version exists

cableprobe upgrade queries PyPI itself (so it is not fooled by a stale pip index cache the way pipx upgrade sometimes is), works out how this copy was installed — pipx, pip, scripts/install.sh, a source checkout — and runs the right upgrade with the cache bypassed. Then:

cableprobe --version
cableprobe check

Doing it by hand instead:

# pipx, to the latest release — add --no-cache-dir if it claims you're up to date
pipx upgrade cableprobe --pip-args=--no-cache-dir
pipx install --force cableprobe==0.3.10        # pin / roll back to a version

# pipx, to the latest development code (main), ahead of the last release
pipx install --force "cableprobe @ git+https://github.com/rosscooney/CableProbe@main"

# scripts/install.sh install — re-run it against a fresh checkout
git -C cableprobe pull && sudo ./cableprobe/scripts/install.sh

# development checkout
git pull && pip install -e ".[dev]"

If a release drops a probe or changes report fields it is called out in the GitHub release notes and CHANGELOG.md; saved .cableprobe.json reports from older versions still open with cableprobe report.

Usage

# Check the host is ready
cableprobe check

# Run a session (you will be prompted before each phase; a progress bar
# tracks each phase's timer)
sudo cableprobe run --name "suspect-cable-01" \
    --baseline 30 --test 90 --post-test 30

# Unattended / rig mode: advance phases on a timer instead of prompts
sudo cableprobe run --auto --baseline 20 --test 60 --post-test 20

# Inspect a saved report
cableprobe report                         # lists saved reports, asks which
cableprobe report cableprobe-sessions/2026*.cableprobe.json
cableprobe report <file> --format json | jq .

# See / customise detection rules
cableprobe rules
cableprobe rules my-rules.yaml

Running with sudo is strongly recommended: without root the kernel-log, udev-attribute, USB-descriptor, keystroke-timing and raw-socket probes see much less detail and some are skipped entirely. cableprobe run detects this and, in interactive mode, prints the sudo command and asks whether to continue anyway; --auto just warns and proceeds. cableprobe check flags it too.

sudo: cableprobe: command not found? A pipx / pip install --user install puts cableprobe in ~/.local/bin, which is not on root's PATH. Fix it permanently — run this once (no sudo in front; it escalates itself and asks for your password):

cableprobe link          # cableprobe link --remove to undo

after which sudo cableprobe run just works. Or, per-invocation: run it by absolute path (sudo "$(command -v cableprobe)" check) or preserve your PATH (sudo env "PATH=$PATH" cableprobe check). The not-root warning prints whichever of these applies to your install. (scripts/install.sh, below, sets the link up as part of a from-scratch /opt install.)

Exit codes

cableprobe run --fail-on-findings exits 10 / 20 / 30 for the highest finding severity (medium / high / critical), otherwise 0. Without the flag, run always exits 0 on a completed session.

Configuration

Optional YAML config (--config cableprobe.yaml):

session:
  baseline_seconds: 30
  test_seconds: 90
  post_test_seconds: 30
  sample_interval_seconds: 2.0
probes:
  # the default set; list a subset to narrow the session, or add `wifi_scan`
  enabled: [udev_monitor, usb, usb_descriptors, usb_topology, usbc_pd, block,
            mounts, network, routing, listeners, input, serial, audio, video,
            pci, kernel_modules, keystroke_cadence, process, kernel_log]
  kernel_log_backend: auto        # auto | journalctl | dmesg
  kernel_log_keywords: []         # extra case-insensitive substrings to keep
  kernel_log_verbose: false       # true => also keep routine enumeration chatter
  capture_process_cmdline: true   # false => store only the executable name
  capture_keystroke_timing: true  # false => disable the keystroke_cadence probe
rules_file: null                  # null => packaged default rules
output_dir: ./cableprobe-sessions

Reports are written with mode 0600 (they can contain host details, MAC addresses and process command lines). All device-supplied text (USB descriptor strings, device names, kernel log lines) is stripped of control characters and length-bounded before it is stored or shown, so a hostile cable cannot inject terminal escape sequences via the report or the console summary.

Detection rules

Rules live in YAML (see cableprobe/data/default_rules.yaml). Each rule matches a phase delta and raises a finding:

- id: hid-keyboard-appeared-on-connect
  title: HID keyboard appeared while the unknown cable was connected
  severity: high
  rationale: >
    A keyboard-class HID device that enumerates only when the cable is
    connected is the classic BadUSB signature.
  match:
    change: appeared          # appeared | disappeared | modified
    first_seen_phase: test    # baseline | test | post_test
    kind: [input_device, hid_device]
    attributes:
      any:
        - { key: ID_INPUT_KEYBOARD, equals: "1" }

Match keys: change, kind, first_seen_phase, reverted_after_disconnect, transient, label_regex, event_action, and attributes.all / attributes.any (conditions: equals, not_equals, exists, contains, not_contains, regex).

Report structure

{
  "metadata":  { "session_name", "host", "config", "probes_used", "probe_warnings", ... },
  "phases":    { "baseline": {...}, "test": {...}, "post_test": {...} },
  "deltas":    [ { "change", "kind", "identity", "label",
                   "first_seen_phase", "present_in",
                   "reverted_after_disconnect", "transient",
                   "attributes", "attribute_changes", "related_events" } ],
  "findings":  [ { "rule_id", "title", "severity", "rationale", "evidence" } ],
  "summary":   { "delta_count", "cable_correlated_change_count",
                 "findings_by_severity", "highest_severity", ... }
}

Development

pip install -e ".[dev]"
pytest

The analysis, rules and report layers are pure and fully unit-tested without hardware. Each probe keeps a pure parser (of lsusb / lsblk / /proc output) or sysfs-tree scanner that is tested against captured samples or a fake /sys tree — see tests/test_probes_parsing.py and tests/test_probes_new.py.

The source lives at https://github.com/rosscooney/CableProbe. See CHANGELOG.md for what changed in each release, CONTRIBUTING.md for how to contribute, SECURITY.md for how to report vulnerabilities privately, and RELEASING.md for how maintainers cut a release to PyPI.

Scope / non-goals

• CLI only — no web dashboard.
• The usbc_pd probe reads the kernel's USB-C / Power Delivery port state (data/power roles, alternate modes); CableProbe does not do electrical measurement of the cable itself — no voltage/current sampling, no e-marker interrogation.
• No offensive capability of any kind, by design.

Third-party dependencies

CableProbe does not copy or vendor third-party source code. It depends on a small set of Python libraries and, at runtime, invokes standard Linux command-line tools as separate, independently installed programs. See NOTICE.md and the "Third-party licensing" note below in the repo history / docs.

Direct Python dependencies and their licences:

Note on pyudev: pyudev is LGPL-2.1-or-later. It is a normal, separately installed Python dependency that CableProbe imports; it is not vendored or modified. Distributing an MIT-licensed project that depends on an unmodified LGPL library is standard practice, provided pyudev remains replaceable and its source stays available (it is, from PyPI). If you redistribute CableProbe as a bundled binary/image, keep pyudev as a replaceable component and include its licence text. The Linux CLI tools CableProbe shells out to (lsusb/usbutils, lsblk/dmesg/util-linux — GPL-2.0; journalctl/systemd — LGPL-2.1) are invoked as independent programs and do not affect CableProbe's MIT licensing.

Licence

CableProbe is open-source software created by Stable State Consulting Ltd and released under the MIT License.

Copyright © 2026 Stable State Consulting Ltd.

See LICENSE for details.