minsnap_trajectories 0.0.1

Simple minimum-snap trajectory generator

Minsnap Trajectories

Simple Python/Numpy implementation of the Minimum Snap Trajectory Generation algorithm.

This package addresses the shortage of turnkey minsnap trajectory generator implementations on PyPI. It implements two of the most time-tested algorithms in this area:

• Mellinger and Kumar's original Minimum Snap Trajectory Generator [1]

• Roy and Bry's numerically stable, unconstrained quadratic program [2]

and an important utility in generating quadrotor trajectories:

• Aerodynamic-effects-aware flatness map from flat outputs to quadrotor state and inputs

---

[1]: D. Mellinger and V. Kumar. Minimum snap trajectory generation and control for quadrotors. In Proc. Int. Conf. on Robotics and Automation, 2011

[2]: C. Richter, A. Bry, and N. Roy. Polynomial trajectory planning for aggressive quadrotor flight in dense indoor environments. In Int. Symposium on Robotics Research, 2013

Get Started

Note that this package is imported as follows

import minsnap_trajectories as ms

TLDR

Four key names

• ms.Waypoint: Time, position, velocity, etc. waypoint. A sequence of this defines the trajectory
• ms.generate_trajectory: Generates the piecewise-polynomial trajectory
• ms.compute_trajectory_derivatives: Samples the polynomial for position/velocity/acceleration, etc.
• ms.compute_quadrotor_trajectory: Directly compute quadrotor state/inputs along the trajectory

Full usage example

Define a sequence of position (and optionally velocity, acceleration, higher-order) references

refs = [
    ms.Waypoint(
        time=0.0,
        position=np.array([0.0, 0.0, 10.0]),
    ),
    ms.Waypoint(  # Any higher-order derivatives
        time=8.0,
        position=np.array([10.0, 0.0, 10.0]),
        velocity=np.array([0.0, 5.0, 0.0]),
        acceleration=np.array([0.1, 0.0, 0.0]),
    ),
    ms.Waypoint(  # Potentially leave intermediate-order derivatives unspecified
        time=16.0,
        position=np.array([20.0, 0.0, 10.0]),
        jerk=np.array([0.1, 0.0, 0.2]),
    ),
]

Generate a piecewise polynomial trajectory using Roy and Bry's closed form solution, minimizing jerk (order-3) AND snap (order-4) while constraining position, velocity, etc... up to jerk (orders 0 to 3) to be continuous

polys = ms.generate_trajectory(
    refs,
    degree=8,  # Polynomial degree
    minimized_orders=(3, 4),  
    continuous_orders=3,  
    algorithm="closed-form",  # Or "constrained"
)

# Inspect the output
t = polys.time_reference
dt = polys.durations
cfs = polys.coefficients

Sample the polynomial trajectory to get position, velocity, acceleration (or higher-order) trajectories

t = np.linspace(0, 16, 100)
#  Sample up to the 3rd order (acceleration) -----v
pva = ms.compute_trajectory_derivatives(polys, t, 3)
position = pva[0, ...]
velocity = pva[1, ...]

Or directly generate a quadrotor UAV trajectory

t = np.linspace(0, 15, 100)
states, inputs = ms.compute_quadrotor_trajectory(
    polys,
    t,
    vehicle_mass=1.0, # Quadrotor weight
    yaw="velocity", # Align yaw angle to quadrotor velocity
    drag_params=ms.RotorDragParameters(0.1, 0.2, 1.0),
)

Limitations

Tests are not nearly enough!

Existing tests show that this piecewise polynomial planner behaves identically to two of the more approachable MATLAB-based trajectory generator implementations by icsl-Jeon and symao.

1. The polynomial planner is not well-guarded against the case when the polynomial planning problem is overconstrained, i.e.

   • The polynomial degree is too low
   • Too many orders of derivatives are constrained to be continuous

2. The quadrotor trajectory generator is not extensively tested (the rotor-drag effect compensation function is even more so).

Until more extensive tests are available, use the following parameters in polynomial planning (they are the defaults)

• degree: From 5 to 15
• minimized_orders: 5 (Minimum snap)
• continuous_orders: 3 (Just keep position/velocity/acceleration continuous)