napalm-hios 1.2.1

NAPALM driver for HiOS network switches by Belden

NAPALM HiOS Driver

NAPALM driver for Hirschmann HiOS industrial switches by Belden. Supports SSH and SNMPv3 protocols with full getter parity across both.

Features

• Dual protocol: SSH and SNMPv3 with automatic failover
• SNMPv3 authPriv (MD5/DES) — works with HiOS factory defaults including short passwords
• 20 getters on both SSH + SNMP, plus 3 SSH-only methods and 3 SSH-only write operations
• Vendor-specific: MRP ring redundancy, HiDiscovery, extended LLDP, config save/status
• Comprehensive unit tests (146+) and live device validation

Installation

To install the NAPALM HiOS driver, run:

pip install napalm-hios

Quick Start

Here's a basic example of how to use the NAPALM HiOS driver:

from napalm import get_network_driver

# Initialize the driver
driver = get_network_driver('hios')
device = driver(
    hostname='your_device_ip',
    username='your_username',
    password='your_password',
    optional_args={'ssh_port': 22}  # Optional: specify SSH port if different from default
)

# Open the connection
device.open()

# Use NAPALM methods
facts = device.get_facts()
interfaces = device.get_interfaces()

# Close the connection
device.close()

If you want to see it in action without a specific purpose or use case, simply create your virtual environment, install with the pip command above and then execute the test_hios.py file found in examples/test_all_commands.py This command takes [ip address for ping] [count] (with the later two being optional) it will log the json returned dicts into the current folder in a file called test_live_device.md

Documentation

For detailed information about the NAPALM HiOS driver, including supported methods, advanced usage, and error handling, please refer to the comprehensive documentation. This docuemntation was written by Claude from Anthropic so if anything is wrong I take no responsibility.

Supported Methods

Standard NAPALM getters (SSH + SNMP)

• get_facts()
• get_interfaces()
• get_interfaces_ip()
• get_interfaces_counters()
• get_lldp_neighbors()
• get_lldp_neighbors_detail()
• get_mac_address_table()
• get_arp_table()
• get_ntp_servers()
• get_ntp_stats()
• get_users()
• get_optics()
• get_environment()
• get_snmp_information()
• get_vlans()

SSH-only standard methods

• get_config() — CLI scraping
• ping() — device-originated ping
• cli() — raw command execution

Vendor-specific methods (SSH + SNMP)

• get_mrp() — MRP ring redundancy status
• get_hidiscovery() — HiDiscovery protocol status
• get_lldp_neighbors_detail_extended() — LLDP with 802.1/802.3 extensions
• get_config_status() — check if running config is saved to NVM
• save_config() — save running config to NVM

Vendor-specific write operations (SSH-only)

• set_mrp() — configure MRP ring on default domain
• delete_mrp() — disable and delete MRP domain
• set_hidiscovery() — set HiDiscovery mode (on/off/read-only)

Note: Configuration-related methods (load_merge_candidate(), load_replace_candidate(), compare_config(), commit_config(), discard_config(), rollback()) are not implemented — HiOS does not support candidate configurations.

For vendor-specific method details, see docs/vendor_specific.md. For standard method details, see docs/usage.md.

Example

python -m examples/ssh_examply.py

Note: the example runs with user permissions against an online application lab provided by Hirschmann in Germany, this limits which commands you can execute.

For more details about the application lab, see http://applicationlab.hirschmann.de/remoteaccess

Testing

To run the unit tests:

python -m unittest discover tests/unit

Note: tests are still a work in progress...

To run the integration tests (requires a real HiOS device or a properly configured mock):

python -m unittest discover tests/integration

Note: I've been using example/test_all_commands.py against real devices by calling it with , the ping ip and count are optional and will default to 8.8.8.8 if not specified. This writes results to test_live_device.md and i've included an example output from a live device

Mock Device

The driver includes a mock HiOS device for testing and development purposes. To use the mock device, set the hostname to 'localhost' when initializing the driver.

Note: The mock device functionality is still in development

To-do

Some musings about what to do for next release, Wishlist, feel free to make suggestions if you have a specific need.

Protocol Support

The driver supports SSH and SNMPv3 protocols, selected via protocol_preference in optional_args. Default order: SSH → SNMP → NETCONF.

SNMP Configuration

SNMPv3 authPriv (MD5/DES) is used when a password is provided — this matches HiOS factory defaults where SNMPv1/v2c are disabled. HiOS CLI users are the SNMPv3 users (same username/password). Falls back to SNMPv2c when password is empty (community-only mode).

device = driver(
    hostname='192.168.1.4',
    username='admin',
    password='private',
    optional_args={'protocol_preference': ['snmp']}
)

Short passwords (< 8 chars, including the HiOS default private) are handled by pre-computing the MD5 master key, bypassing pysnmp's RFC 3414 minimum length enforcement.

SSH vs SNMP — Known Differences

Both protocols implement the same NAPALM getters, but there are inherent differences in the data returned:

#	Area	SSH	SNMP	Impact
1	cpu/1 interface	Not exposed	Exposed via IF-MIB	SNMP returns +1 interface in get_facts, get_interfaces, get_interfaces_counters, get_interfaces_ip
2	MAC addresses	Base MAC (same for all ports, uppercase)	Per-port incrementing MAC (lowercase)	get_interfaces mac_address field differs
3	Speed on down ports	Shows configured speed	ifHighSpeed=0 when link is down	get_interfaces speed field differs for down ports
4	Counters	32-bit counters	64-bit HC counters (more accurate)	SNMP counters wrap at 2^64 instead of 2^32
5	VLANs	Configured membership only	Egress bitmap (superset)	SNMP get_vlans may show extra ports
6	ARP on L2 devices	Fails gracefully (empty list)	Returns empty (no error)	Both return [], but SSH may log a warning
7	SNMP communities	Readable via CLI	Cannot query via SNMP (security)	SNMP get_snmp_information always has empty community dict
8	ARP age	Calculated from CLI output (seconds)	Always 0.0 (not in standard MIB)	get_arp_table age field differs on L3 devices
9	LLDP system capabilities	Not exposed by HiOS CLI	Decoded from LLDP-MIB bitmap	SSH remote_system_capab is always [], SNMP returns actual capabilities
10	Management interface name	vlan/N (from CLI)	cpu/1 (from IF-MIB)	get_interfaces_ip key name differs
11	HiDiscovery relay	Omitted on L2 devices (CLI doesn't output it)	Always present (MIB returns a value)	SNMP get_hidiscovery may include relay field when SSH doesn't

Implementation Priority

When implementing getters, this priority order is followed:

1. NAPALM spec compliance — match the standard return format
2. SSH/SNMP alignment — same keys, same structure, minimal surprises
3. Raw OID accuracy — use the most precise MIB data available
4. Error handling — graceful degradation, never crash on missing data

Getter Availability by Protocol

Method	SSH	SNMP	Notes
get_facts	Yes	Yes
get_interfaces	Yes	Yes
get_interfaces_ip	Yes	Yes
get_interfaces_counters	Yes	Yes
get_lldp_neighbors	Yes	Yes
get_lldp_neighbors_detail	Yes	Yes
get_lldp_neighbors_detail_extended	Yes	Yes	Vendor; SNMP adds 802.1/802.3 data
get_mac_address_table	Yes	Yes
get_arp_table	Yes	Yes
get_vlans	Yes	Yes
get_snmp_information	Yes	Yes
get_environment	Yes	Yes
get_optics	Yes	Yes
get_users	Yes	Yes
get_ntp_servers	Yes	Yes
get_ntp_stats	Yes	Yes
get_mrp	Yes	Yes	Vendor (MRP ring redundancy)
get_hidiscovery	Yes	Yes	Vendor (HiDiscovery protocol)
get_config_status	Yes	Yes	Vendor (NVM/ACA/boot sync state)
save_config	Yes	Yes	Vendor (save running-config to NVM)
get_config	Yes	No	SSH-only (CLI scraping)
ping	Yes	No	SSH-only
cli	Yes	No	SSH-only
set_mrp / delete_mrp	Yes	No	SSH-only write operations
set_hidiscovery	Yes	No	SSH-only write operation

Known Issues

• If a method is only available on SSH (e.g. get_config, ping, cli, write operations) and the active connection is SNMP, calling it raises NotImplementedError.
• NETCONF support is stub-only — not usable for production.

Contributing

Contributions to the NAPALM HiOS driver are welcome! Please refer to the CONTRIBUTING.md file for guidelines.

License

This project is licensed under the Apache License 2.0 - see the LICENSE file for details.