nff 0.1.1

Claude Code IoT Bridge — connect Claude to hardware via USB

nff — Claude Code IoT Bridge

nff connects Claude Code to physical hardware over USB. It exposes your board as a set of MCP tools so Claude can autonomously write firmware, compile it, upload it, read serial output, and debug — all from a single conversation.

you: "Make the LED blink every 200 ms and print the state to serial"
Claude: [writes sketch] → [compiles] → [uploads to ESP32] → [reads serial] → done

Supported boards (v1): Arduino Uno · Mega · Nano · Leonardo · ESP32 (CP210x / CH340) · ESP8266 (FTDI)

---

Quickstart

1. Install

pip install nff

2. Plug in your board, then run init

nff init

nff init does three things automatically:

• Detects your board by USB vendor/product ID
• Installs arduino-cli if it isn't on your system yet
• Registers the nff MCP server in ~/.claude/claude_desktop_config.json

Expected output:

  ✓ Found: ESP32 (CP210x) on COM10 (vendor: 10c4, product: ea60)
  ✓ arduino-cli installed.
  ✓ Config written to C:\Users\you\.nff\config.json
  ✓ MCP config written to C:\Users\you\.claude\claude_desktop_config.json

3. Verify everything works

nff doctor

All checks should be green. If arduino-cli boards/cores are missing, install them:

arduino-cli core install arduino:avr      # Arduino boards
arduino-cli core install esp32:esp32      # ESP32
arduino-cli core install esp8266:esp8266  # ESP8266

4. Open Claude Code and start talking to your hardware

Restart Claude Code (or Claude Desktop) so it picks up the new MCP server. You're ready.

---

CLI Reference

Command	Description
nff init	Detect board, install arduino-cli, write config, register MCP server
nff flash <file>	Compile and upload a .ino sketch or sketch directory
nff monitor	Interactive serial monitor (Ctrl+C to exit)
nff doctor	Check all dependencies and configuration
nff install-deps	Re-download and install arduino-cli
nff mcp	Start the MCP server (called automatically by Claude Code)

nff flash

nff flash ./blink.ino
nff flash ./my_sketch/                       # sketch directory
nff flash ./blink.ino --board arduino:avr:uno --port COM3
nff flash ./blink.ino --manual-reset         # for boards with broken auto-reset

nff monitor

nff monitor
nff monitor --port COM10 --baud 115200
nff monitor --timeout 10                     # stop after 10 seconds

---

MCP Tools (what Claude can call)

Once registered, Claude Code has access to these tools:

Tool	What it does
list_devices()	List all connected USB boards
flash(code, board?, port?)	Write, compile, and upload a sketch
serial_read(duration_ms?, port?, baud?)	Capture serial output for N ms
serial_write(data, port?, baud?)	Send a string to the device
reset_device(port?)	Toggle DTR to hardware-reset the board
get_device_info(port?)	Return port, board name, FQBN, baud rate

All tools fall back to the default device in ~/.nff/config.json when port and board are omitted.

---

Config file

Stored at ~/.nff/config.json, written by nff init, editable by hand:

{
  "version": "1",
  "default_device": {
    "port": "COM10",
    "board": "ESP32 (CP210x)",
    "fqbn": "esp32:esp32:esp32",
    "baud": 115200
  }
}

---

Supported Boards

Board	Vendor ID	Product ID	FQBN
Arduino Uno	2341	0043	arduino:avr:uno
Arduino Mega 2560	2341	0010	arduino:avr:mega
Arduino Leonardo	2341	0036	arduino:avr:leonardo
Arduino Nano	2341	0058	arduino:avr:nano
ESP32 (CP210x)	10c4	ea60	esp32:esp32:esp32
ESP32 (CH340)	1a86	7523	esp32:esp32:esp32
ESP8266 (FTDI)	0403	6001	esp8266:esp8266:generic

Board not listed? Open a PR — adding one is two lines of code.

---

Linux: serial port permissions

On Linux, serial ports require the dialout group:

sudo usermod -aG dialout $USER
# then log out and back in

nff doctor will detect this and print the fix if your port is inaccessible.

---

Repository structure

nff/
├── nff/
│   ├── cli.py              # Click entry point — routes subcommands
│   ├── mcp_server.py       # MCP server — registers all tools for Claude
│   ├── config.py           # Read/write ~/.nff/config.json
│   ├── commands/
│   │   ├── init.py         # nff init
│   │   ├── flash.py        # nff flash
│   │   ├── monitor.py      # nff monitor
│   │   └── doctor.py       # nff doctor
│   └── tools/
│       ├── boards.py       # USB vendor ID detection
│       ├── serial.py       # pyserial read/write/stream
│       ├── toolchain.py    # arduino-cli subprocess wrappers
│       └── installer.py    # arduino-cli auto-installer
├── scripts/
│   └── install_arduino_cli.py   # Standalone installer (thin wrapper)
├── sketches/
│   └── blink_esp32/        # Example sketch
├── tests/
├── pyproject.toml
└── CONTRIBUTING.md

---

License

MIT — see LICENSE.
Copyright (c) 2026 Gauthier Lechevalier